HE2250 Whirlpool Dryer - Instructions

removed the front of dryer panel below the door. Cleaned out all the lint. Pulled two screws with an extended nut driver. slid out the old element. I dentified the part . ordered, when the part came in I put a few simple componets on the new, slid it back in. Turned on the power to make sure it was working then reinstalled the front cover. works fine

To start the repair, I removed the two front panels. Disconnecting the wiring to door and light. Next removing dryer drum and drive belt[ allows access to belt tensioner] replace tensioner roller, then reassemble. Dryer works fine

clothes drier didn't work, tore the drier apart, found problem went looking for the part locally, didn't find it, got mad, went on line, found Parts Select, ordered part, part under $20.00 delivered, part delivered, put everything back together , can dry clothes again, didn't have to find $350.00 to go buy a new drier. Merry Christmas!

You have to take apart the whole dryer to get to the belt.Nut driver with cordless drill make it go so much faster.Unplug dry, take apart dryer and replace with olr belt with new belt.Takes about 20 minutes to do.plus I took off the two guide wheels on back of cabinet and greased everything.Works like brand new.I had a repair guy tell me I needed a new motor.If you can spin the drum by hand replace belt first.

used one nut driver, basically took the whole machine apart. took snap ring off the idler shaft, replaced pulley, and put it back together. simple job.

removed the lower cover, tipped the dryer on its back for easier access, unscrewed the 2 mounting screws removed the heating element, installed the thermostat and and high tempt relay on new one replaced the wires reinstalled the new element, very simple

This would be an easy job, if I were to do it again.

I needed to download a manual only to get ACCESS to the machine. Removing the outside lag bolts did NOT provide access.

They had hidden clips that were ENTIRELY invisible from the outside. I believe this was done deliberately, to prevent those who don't know the specifics about this machine from gaining access.

It's an easy job, once you know the idiosyncracies of the construction of the machine. It's a major pain in the ass if you don't, even if you are used to replacing belts in other dryers.

Having done it once, the next time I could do it in under 20% of the time it took me the first time.

The first time, I inserted the belt the wrong way. The drum turns a little bit then stops. The manufacturer does not give any instructions or drawings on their website on that particular model, only drawing of parts.I called the technical support department and they told me to call different telephone numbers in my area and repair technicians. Still no schematic and instructions.
The solution: I took the broken belt, put around the drum, measured it, the remaining slack, did some trial and error around the motor axle and the pulley.
Placed a 2 X 4 piece of wood to hold the tension of the pulley. With the belt around the drum, carefully inserted the drum downward. placed the belt starting from the left side of the drum to the bottom of the motor axle, around it then to the bottom of the tension pulley, then towards the right side of the drum.
Lift the drum to its proper position, horizontal. Remove the piece of wood. Turn the drum manually so it moves freely. check the belt moving around the axle and the pulley. Install back the panels and screws tightened. Test and observe a few drying runs.

Basically, Followed the instructions in the Video for Belt replacement. I found out however that the Tensioner was also broken aand needed replacement, and this required the snap wring pliers. also spindle on motor was stripped and had to use "lockTite" to repair that. Overall was far better "doining it myself" than paying for repai service which would have cost several hundred $ in costs. This increased my confidence level to know that as long as parts are available I will always be able to repair this appliance!

Just snapped the new plastic latch into the hole (the hole was there because in trying to extract the old latch, it fell into the inside of the door). Took two seconds. Order to arrival of the part took only 22 hours!

Leaned machine back and put blocking under machine to elevate. Removed two screws from front of bottom panel. Lift panel out and set aside. Next remove two bottom screws from door frame. Pull bottom of frame out and up to release. Remove wire clips from door light and switch. Set door frame aside. Inside drum, take three phillips head screws out, that hold filter frame in, remove filter frame. Next remove four front screws on drum alignment face plate. Set aside. Grasp drum and pull forward, off back guide rollers. Drum will drop down a little, reach in around drum and slide belt off. Remember to look in under drum to see proper placement of belt aroun motor shaft and idler pulley. Replace new belt around drum with ribs against drum. Route belt around motor shaft pulley, pull idler pulley toward motor and place belt around pulley smooth top runs against pulley. Reinstall everything you removed. Connect wires to door.

Took apart front of dryer, took out tub, replaced pully wheel, put tub back in with new belt, and put front back on. I would recomend replacing wear pads when doing this type of job.

removed front of dryer, replaced old pully and put on new belt.

removed old element, relaced with new element , thermostat dryer works better than it has in along time

Fairly easy to repair once I figured out how to get it apart. The amazing part of this was searching the web for the part. I found PartSelect, ordered it at about 2pm Eastern time and the part arrived the next day! I will definitely use this service again.