HE2250 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ronald from cathlamet, WA
- Parts Used:
- WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
a pencil jammed the drum and broke the drive belt
remove front panel ,remove top panel,lift drum,slide new belt on to drive motor then idler pulley then put belt over the drum.reassemble in reverse , front panel first
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bryan from lewisburg, TN
- Parts Used:
- WPY54414, WP40111201
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
loud squeaky sound
remove the housing under the dryer door. take out the lint trap. I took the whole bottom off the dryer to easily get to the tensioner pully. I then loosened the tub and slid off the old belt and replaced it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from ROTONDA WEST, FL
- Parts Used:
- 61927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Dryer Would Not Heat
Removed 2 screws on the bottom of front panel of dryer & pulled it off. Next I got down & looked to the back & bottom inside of the dryer. I spyed the heating element,I pulled off the two wires from the thermostats[ orange & black. I removed two screws from the heating element plate & dropped it down & removed it from the dryer. Reverse procedure to reinstall. Will see if we can get another 10 years service out of it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from Sallinas, CA
- Parts Used:
- WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
The drum would not turn is certain positions.
Took off the two lower front screws, Then the screws to take off the door and frame. Then the lint trap. Finally took out the drum. BOY WAS MY DRYER DIRTY WITH LINT! Vacumned it all out and washed the filter and filter housing with soap. Found out that I needed tension wheel also. Ordered that. Replaced the wheel, that was the hardest part. Need to take off this part like a "spring washer" and put it back on with the new wheel in place. Then placed the belt on the drum, belt on the tension, screwed the drum holder frame on, screwed the door frame on, screwed the lower panel on and it works great. By the way I am a female and if I can do it anyone can.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Saginaw, TX
- Parts Used:
- 61927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
unit stop heating
once I found where the heat element was, it took me a few mintues to remove the bad one and replace it with the new one that came before the due date. very good instruction in kit. Be sure and leave the old one hooked up until the new unit comes in so you can do a easy exchange of the wiring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from Charlotte, NC
- Parts Used:
- 56000
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
no heat ... rattle ... no air through vent
Determined no air flow or heat through system even though dryer spun and timer worked. Ouside vent dispelled no air. Opened dryer panel.
Blower wheel/fan broken off from shaft. Googled appliance parts ... found ... Partselect .... keyed in mfg, model number ... schematics available ... found part ... ordered ... received in two days ... installed ... reassembled. Working fine ! $ 30.00 compared to buying new dryer ! This was a refreshing and rewarding repair. If it could always be this smooth !!! Great resource ... PARTSELECT !
Blower wheel/fan broken off from shaft. Googled appliance parts ... found ... Partselect .... keyed in mfg, model number ... schematics available ... found part ... ordered ... received in two days ... installed ... reassembled. Working fine ! $ 30.00 compared to buying new dryer ! This was a refreshing and rewarding repair. If it could always be this smooth !!! Great resource ... PARTSELECT !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Thorntown, IN
- Parts Used:
- WPY54414
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Socket set, Wrench set
Idler Pully squealing
removed bottom panel.Has 2 screws on bottom.take belt off of idler. take 2 screws out of motor base.turn motor sideways& remove bolt from arm that holds idler. remove snapring holding idler. replace pully & reassemble in reverse. Thank You Partselect for prompt shipping. A+ Rating
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Kremmling, CO
- Parts Used:
- WPY54414, WP40111201, WPW10121334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Broken belt and idler pulley.
I followed the belt replacement video and voila, the job was done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from Palisade, CO
- Parts Used:
- WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
drum not turning properly
as described in video. Very well done. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Rochester, NY
- Parts Used:
- 61927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Not much heat
Loosened the screws, took out the old one. It shorted out to back. Inserted the new one attached wires, Installed screws and it worked
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Rancho Mirage, CA
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door catch, male portion, broke off
Popped in the new part. Really! That easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Arlington, MA
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door wouldn't stay closed
I used a screwdriver to pry out the broken door latch and inserted the new one in the same slot. Perfect fit. The picture of the part in the order page was a big help to identify the correct part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ian from Greeley, CO
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door would not stay closed because metal latch piece was gone.
I ordered the part. ( I should have ordered just in case it happens again.) When it got here it took less than a minute to snap it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Columbiana, OH
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door Catch broken
The old door catch broke and fell into the unit. Ordered the new part which arrived fast and snapped it into place. Perfect fit and the door now closes/latches correctly - like new again. Would recommend your web site to all do-it-yourselfers. Loved browsing your site, especially seeing all of the schematics and parts list for my unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Sublette, IL
- Parts Used:
- WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Broken belt
Lifted the top of the dryer removed two screws and pulled the front of the Dryer forward. Slipped the new belt over the drum and over the motor pulley.
Pushed the front back in place and snapped the top of the dryer down and the job was complete.
I thought the part would take three days to get here.
It was delivered the day after I ordered it.
Pushed the front back in place and snapped the top of the dryer down and the job was complete.
I thought the part would take three days to get here.
It was delivered the day after I ordered it.
Was this instruction helpful to you?
Thank you for voting!