Models > YNED4755EW1 > Instructions

YNED4755EW1 Whirlpool Dryer - Instructions

Jump to:

All Instructions for the YNED4755EW1
121 - 135 of 717
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jason from Kettering, OH
Parts Used:
341241
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Dryer wouldn't tumble
First unplug the machine and turn off the gas. Then, I pried the top up (2 clamps on front, 2 screws to the lint screen). Then I removed 2 5/16 nuts that fastened front panel to sides. I held the drum and pried the front panel back while my wife slipped the new belt around the drum. Then, I buttoned everything back up in reverse order, removed the kick panel, threaded the belt through the tensioner pulley and around the motor shaft. It's really that easy. PartSelect.com makes it simple with quick, accurate service.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from McAllen, TX
Parts Used:
341241
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
drum would not turn
Once I realized it was just a drum belt and how easy it was to fix, I ordered the belt myself with no help from a national warehouse hardware chain where the manager said "I don't have a belt but I can sell you a dryer." Thank you I kept my 300+ dollars and once I got the belt it only required removing the two screws that sealed the lint screen cannel to the top; popping the top, removing the to nutbolts fastening the front to the side panels; slidding the front panel out; putting the belt around the drum and attaching it properly to the tension pully and motor. Finally, I closed it up and tested it. Household hero in less than 12 minutes! Not bad for a psychologist, eh?
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Germantown, TN
Parts Used:
341241
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Replace belt
Disconnect power. Removed front panel and lifted top. Removed belt around spring pully and motor assembly. Carefully eased belt around back of drum and gasket. Reverse process.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
MARY from PORT ALLEN, LA
Parts Used:
4392065
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Belt
My son did the repairs it took less than 30 minutes it's an old dryer so glad to be able to get the parts. I do not like the new dryers because of all the pushbuttons thanks so much for the ports
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lawrence from SOUND BEACH, NY
Parts Used:
341241
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Drum would not spin
Needed a belt. Only snag was for me was re-installing front panel (door)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from MYRTLE BEACH, SC
Parts Used:
4392065
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
noisy dryer
followed the enclosed instructions, used a balled up towel to support the drum while attaching the belt and tension pulley, took about 20 minutes
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ed from GRAFTON, IL
Parts Used:
WP3387134
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Clothes never completely dry
I watched the video then called them to order parts. They were VERY helpful & NICE. I had the parts the NEXT day. I followed the video instructions & it worked. They made my day! THANK YOU JoAnn & Teresa!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sherry from TUJUNGA, CA
Parts Used:
WP3387134
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Clothes taking too long to dry.
The dryer was igniting when initially starting load, but didn't light again the rest of the cycle. On my model the access was through the front panel, didn't even have to pull dryer out. Open the door and there are two screws on each side.of the inside of frame. Remove screws and lift door off the the whole front of the pulls out and down and removes, and everything is right there to work on. Replaced thermostat, that took 5 min. But didn't fix the problem. So I purchased and replaced the "M" Series New Style Coil Kit, took about 10 min. I took olm/continuity readings b/t all terminals of the old and new coils and they were only about 5% difference, the old being a little lower. But that fixed the problem, works like new again.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Beatrice from WALTHAM, MA
Parts Used:
W11778253
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
replaced the dryer lint screen filter
removed the old damaged filter and replaced with the new one
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from FAIRPORT, NY
Parts Used:
W11778253
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Handle broke off of the Lint filter
Removed old filter and replaced with the new one.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
mark from WINCHESTER, VA
Parts Used:
341241
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
Broken belt
Watched a video and went to town taking it apart. I stuck a pop can under the barrel to hold it up while I worked on pulleys. My dryer does not have a plastic pulley but a metal tension bar with a hole in the middle. Ran upstairs and watched a different video with my set up and all was good. 5 min of work 5 min watching Youtube and 5 min cleaning all the lint out of the machine. I am actually glad the old belt broke because some of the lint was in a clump and had scorch marks on it. I took the shop vac to every part of the cabinet and shoved it down the lint trap sleeve also.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carmen from CUSHING, ME
Parts Used:
W11778253
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Had a torn lint filter
Removed replacement from box. Threw old one out, the new one fit perfectly, and securely.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bernard from Hadley, NY
Parts Used:
341241
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Belt was old & slipping.
- Unplug the electric dryer.
- Manually opened the top of the dryer.
- Unclipped the wire assembly attached to the front panel of the dryer.
- Removed two screws holding the front panel of the dryer, and remove front panel for access.
- Very Important!! Note how the old dryer is currently installed before proceeding.
- Rotated the dryer drum while working the dryer belt toward the rear of the dryer.
- Removed the dryer drum.
- Removed the old dryer belt.
- Put the new dryer belt around the dryer drum and put the dryer drum back onto the drum rollers and into the rear guides.
- Here's the hard part, lay on floor and reach into the pulley area and motor - wrap new dryer belt around these belt rollers as "noted" in the fifth step.
- Rotate dryer drum by hand to ensure the new dryer belt is exactly installed as the old dryer belt.
- Reinstall front panel.
- Reclip wire assembly onto the front panel.
- Manually close the top of the dryer.
- Plug in the electric dryer.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jason from Farmingdale, NY
Parts Used:
341241
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
dryer would not spin
Step 1. Read all the comments about how to do this job in this forum. (i found them very useful)

Step 2. Read the directions that come with the dryer (they helped a lot)

Step 3. Don't forget to disconnect the power cord before reattaching the door switch wires (oucH! ) or doing anything with your dryer.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Mobile, AL
Parts Used:
341241
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The belt that turns the drum broke.
Removed the two screws holding in the Filter and removed the filter.

Removed the two screws holding the front onto the dryer.

Put the belt over the drum and proped the drum up.

Reseated the tension spring and pully in the proper slot. (On my machine it is the position closest to the motor).

Reassembled the dryer in the reverse order.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the YNED4755EW1
121 - 135 of 717