AEE933 Whirlpool Dryer - Instructions

remove front panel ,remove top panel,lift drum,slide new belt on to drive motor then idler pulley then put belt over the drum.reassemble in reverse , front panel first

Determined no air flow or heat through system even though dryer spun and timer worked. Ouside vent dispelled no air. Opened dryer panel.
Blower wheel/fan broken off from shaft. Googled appliance parts ... found ... Partselect .... keyed in mfg, model number ... schematics available ... found part ... ordered ... received in two days ... installed ... reassembled. Working fine ! $ 30.00 compared to buying new dryer ! This was a refreshing and rewarding repair. If it could always be this smooth !!! Great resource ... PARTSELECT !

as described in video. Very well done. Thank you

Loosened the screws, took out the old one. It shorted out to back. Inserted the new one attached wires, Installed screws and it worked

Popped in the new part. Really! That easy!

I used a screwdriver to pry out the broken door latch and inserted the new one in the same slot. Perfect fit. The picture of the part in the order page was a big help to identify the correct part.

removed the front of dryer panel below the door. Cleaned out all the lint. Pulled two screws with an extended nut driver. slid out the old element. I dentified the part . ordered, when the part came in I put a few simple componets on the new, slid it back in. Turned on the power to make sure it was working then reinstalled the front cover. works fine

Lifted the top of the dryer removed two screws and pulled the front of the Dryer forward. Slipped the new belt over the drum and over the motor pulley.
Pushed the front back in place and snapped the top of the dryer down and the job was complete.
I thought the part would take three days to get here.
It was delivered the day after I ordered it.

I ordered the part. ( I should have ordered just in case it happens again.) When it got here it took less than a minute to snap it in.

The old door catch broke and fell into the unit. Ordered the new part which arrived fast and snapped it into place. Perfect fit and the door now closes/latches correctly - like new again. Would recommend your web site to all do-it-yourselfers. Loved browsing your site, especially seeing all of the schematics and parts list for my unit.

once I found where the heat element was, it took me a few mintues to remove the bad one and replace it with the new one that came before the due date. very good instruction in kit. Be sure and leave the old one hooked up until the new unit comes in so you can do a easy exchange of the wiring.

removed old element, relaced with new element , thermostat dryer works better than it has in along time

Just snapped the new plastic latch into the hole (the hole was there because in trying to extract the old latch, it fell into the inside of the door). Took two seconds. Order to arrival of the part took only 22 hours!

Leaned machine back and put blocking under machine to elevate. Removed two screws from front of bottom panel. Lift panel out and set aside. Next remove two bottom screws from door frame. Pull bottom of frame out and up to release. Remove wire clips from door light and switch. Set door frame aside. Inside drum, take three phillips head screws out, that hold filter frame in, remove filter frame. Next remove four front screws on drum alignment face plate. Set aside. Grasp drum and pull forward, off back guide rollers. Drum will drop down a little, reach in around drum and slide belt off. Remember to look in under drum to see proper placement of belt aroun motor shaft and idler pulley. Replace new belt around drum with ribs against drum. Route belt around motor shaft pulley, pull idler pulley toward motor and place belt around pulley smooth top runs against pulley. Reinstall everything you removed. Connect wires to door.

replaced the limit thermostat,thermal fuse, and cycling thermostat. Bingo. Problem solved. Noticed that the back of cycling thermostat had a buildup of lint and I'm wondering if that acted as insulation and caused a wrong reading of temperature. Did not have to disassemble dryer as I could reach all parts with lower front panel removed. To make it easer to install new parts with one hand I lightly hot glued the screws through the new parts and taped the upper portion of new part to bulkhead. With everything lined up and no need to hold the screws I was able to attach using one hand. It was a reach but easily done.