Models > BVLR333GT0WW > Instructions

BVLR333GT0WW Whirlpool Dryer - Instructions

Jump to:

All Instructions for the BVLR333GT0WW
121 - 135 of 225
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Scott from Blackstone, MA
Parts Used:
279834
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Clothes are not drying
Opened the dryer door - removed two screws on the left and two screws on the right - pulled the front panel forward and lifted it up to remove. The coils were located on the bottom right hand corner of the dryer, I vacuumed he area and then removed the two screws and bracket which hold the coil in place. Lifted the new coils off paying close attention to their orientation. Installed new coils. Align tab on top of coils with bracket. installed bracket and screws. Tested dryer and then replaced front cover. Very easy and rewarding.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Kingman, AZ
Parts Used:
279834
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
not heating
two screws on lint screen push up top two screws on front cover. two screws on coils lift coils off put back together. less than 10 minutes. all done
Was this instruction helpful to you?
Thank you for voting!
Customer:
Louis F from West Tisbury, MA
Parts Used:
279834
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The dryer would light in the beginning of the cycle and not come back on
I opened the 5x5" door in the front of the dryer. Unscrewed the clamp holding the two coils down replaced/reconnected the coils and screwed the clamp back down
Was this instruction helpful to you?
Thank you for voting!
Customer:
alan from saint joseph, IL
Parts Used:
279834
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
gas would not stay on
replaced the two coils, which took about 10 minutes
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Oakland, MI
Parts Used:
279834
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Gas only came on for the first time. Wouldn't 'light' after that.
Followed videos seen on the internet for my dryer's repair. Went exactly as shown.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from La Crescenta, CA
Parts Used:
279834
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Dryer quit heating.
Removed two screws from front panel and lifted front panel away, Turned it to the left so I could keep the door switch connected. The dryer would heat when it was first started, but then the burner would go off and would not come back on. I ran the dryer with the front panel off and could see the igniter glow and light the burner, but after the burner cycled off, the igniter would come back on but the gas would not come back on. I could tell it wasn't the thermostat because the igniter would come on, so I knew it must be the gas valve, and therefore probably the coils. The instructions on the website said that the coils were frequently intermittent, so that seemed like the problem. I tried checking out the coil resistance with an ohmmeter to try to confirm that, but couldn't really tell anything that way. I ordered the replacement coils Tuesday night, selecting the cheapest shipping; they shipped on Wednesday, and were delivered on Thursday! Amazingly fast! Removed two screws from the clip that holds the coils in place, unplugged the old coils, swapped in the new coils, screwed the retaining clip back on. All done. Before I replaced the front panel, I watched to see that it operated correctly. I could see the burner cycle off, then after a bit, the igniter glowed, and then the gas came back on and lit, just like it should. Problem solved. Put the front panel back on, and that's all there was to it. Well, I did vacuum out some of the dust inside the cabinet while I had the cover off. Just out of curiosity, I checked the resistance of the new coils before I installed them to compare with the old ones. Couldn't see much difference.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Henry from Weston, MA
Parts Used:
279834
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Dryer would not heat.
Checked heating element and it glowed so I replaced the ceramic gas valve regulators. 4 screws to take front off the dryer and 2 screws to replace part. Couldn't have been easier but I wouldn't have been able to do it without watching the video first.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steve from Glendora, CA
Parts Used:
279834
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Dryer would heat for only a minute, then not re-ignite
Remove the two screws holding the door and lift straight up. Remove the two screws on oppostie side. Face can now be removed by pulling straight out at the top, then lifting face up off of tabs at the bottom. The two coils are at the bottom, held in by a retaining bracket. Remove the screws that hold the bracket. Replace the coils by unplugged their wires. That's it!
Was this instruction helpful to you?
Thank you for voting!
Customer:
dan from macomb, MI
Parts Used:
279834
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
need to replace the coils
Removed 2 screws at the lint filter, unplugged dryer, next I popped the top off with a standard screw driver lifted the top all the way up and secured it from falling back down, used a 5/16" nut driver to remove the top 2 screws holding the face on, disconnected the door switch, pulled the face panel off and set it aside, then I removed the tension pulley on the bottom and took the drum out, unscrewed 2 screws holding the coils removed the old coils and installed the new reconnected the leads to them, vacuumed out the cabinet and motor, inspected all moving parts for wear, including the belt, reinstalled every thing in reverse order, had job complete and ready for clothes in 9 mins, it helps to have your son/daughter hold the drum against the back wall while reconnecting the tensioner and belt.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jahi from San pablo, CA
Parts Used:
279834
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Heating cycle would last 4-8 minutes turn off and come back on 15 min. later and repeat
Removed front panel unscrewed the 2 screws on the coil cover. The coil with two prongs had to upside down 3 the prong coil right side up that only way the cove will fit, plug them in re attach the cover and your done
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sandra from Chicago, IL
Parts Used:
279834, 279834
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Dryer would heat up, then cool off.
After researching the problem, I thought the solution would be to replace the two terminal coil valve, but wasn't 100% sure it wasn't the 3 terminal coil, so I bought both. the dryer is 13 years old so I thought it deserved new coils. My husband was away for the week and I had about 10 loads of laundry to do. I dreaded the thought of going to the laundromat, so I went ahead and ordered the parts, thinking I would call a handyman to install them once they arrived. However, I found a Youtube video showing exactly what I had to do and thought it looked easy enough. I unplugged the machine, removed the front hatch and the 2 small screws holding the coils in place. I unplugged the old coils, used a vacuum to remove the dust in the area and installed the new coils. I popped them back into place, screwed them in, replaced the hatch, plugged the machine in, and VOILA!!!! A dryer that heats!!!!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Pj from Magnolia Springs, AL
Parts Used:
279834
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Gas Dryer not heating.
Unplug the Dryer; remove the lower exterior cover and white plastic drum vent with nut drivers. These two fuses will be setting on top of the function board in front of the gas heating tube.
With a short screwdriver, remove the fuse cover/holder, lift fuse and unplug, replace, re-plug, screw back the cover/holder and you’re done.
Reverse your initial actions...
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nickels from West Allis, WI
Parts Used:
279834
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
the gas would not come on after the igniter lit up.
I replaced the two coils that regulate the gas to turn on and the other to hold open to burn, unplug two connections and remove 2 screws and then replace the coils less then 5 minutes to do this,
Was this instruction helpful to you?
Thank you for voting!
Customer:
Terence from Plymouth, IN
Parts Used:
279834
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
No heat
Igniter would glow and flame would burn for about 30 seconds then a rattling noise would start and the flame would go out. Replaced the coil and all is well. Very simple and inexpensive. One of the easiest repairs I've ever done. Video was very helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nick from Surprize, AZ
Parts Used:
279834
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Dryer would not continue to provide heat to dry laundry.
Both washer and dryer always worked perfectly. Suddenly, dryer wasn’t drying laundry properly. Problem... no heat. Cheapest price I could find calling for appliance service was about $160 to replace coil set but no one would tell me this would fix the problem. This was after calling a number of repair firms and trying to get a somewhat close estimate of what my problem was and what the repair cost. Not knowing, I might have just paid the $160 but what turned me off was having a service call fee of anywhere from $50-$80 with no one willing to tell me what the problem might most likely be before coming out or give me an estimate over the phone other than a range of $160 - $275. I just did not want to have someone come out for $50 -$80 and tell me that I needed to spend $275 and still owe them the service call even if I did not agree.
Found diagnostic and repair instructions help on line. The diagnostic information indicated a high probability, roughly 50%, that replacing the coil set would solve the problem and found the coil set cost $19.21 plus shipping, so I ordered the coil kit for total of $26.70. Note... I am a 71 year old amateur never having worked as a repairman of any kind except for my own needs.
The repair itself took less than 30 minutes start to finish and was one of the most straight forward, glitch free, easy repairs I have ever done. This is a gas dryer but still uses 110 power so I unplugged the 110 power cord from outlet. Followed suggested guidance on opening the dryer cabinet from the front and presto, the coil set I needed to replace was immediately right in front with easy access. Removed 2 screws for the hold-down bracket, slipped off both coils, one at a time, removing the wiring connection for each coil and then reconnecting to each new coil before slipping each new coil back into place and reattaching the hold down bracket. Reinstalled the dryer door and cabinet front in reverse order from taking off... 4 screws total. Plugged in the 110 power cord and put in a damp load of freshly washed laundry. Presto... 30 minutes later... dry laundry. Note... could do the same repair again in half the time since I took it slow and careful 1st time and also took time to remove dust before completing repair. I like things to look like new inside and out and it did when I was done. $26.70 and good as new. Why I didn't spend $160 - $275 is pretty obvious now.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the BVLR333GT0WW
121 - 135 of 225