BVLR333GT0WW Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- daniel from mercedes, TX
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dryer cycles but will not heat
removed front cover and turned unit on, igniter would glow red but burner would not start. ordered m series new style coil kit and installed. turned unit on and igniter came on and burner started right away. all thanks to parts select trouble shooting guide.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Feeding Hills, MA
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Dryer would not heat up
Unplugged the dryer from the wall. Removed the front lower cover. Removed the two screws for the bracket that holds down the coils. Unplugged the coils and swapped them out. Reassembled everything in reverse order. Plugged the dryer back in and started it. It's as good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rafael from SAINT PAUL, MN
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
No flame
when I see its no gas flame, i deduct the flame sensor and the electric coils not fuction, I order tru partselect and that take me like 30 min. to remplaced those parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Montoursville, PA
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Gas dryer would glow but not ignite.
Repair was easy, remove bottom cover, remove screws that hold coil bracket, remove old coils & slip new ones on & button up. Dryer works fine now.Had the new parts within 3 days. Thanks PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sandwich, MA
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Dryer wouldn't heat to dry clothes
First I stumbled around on my own trying to figure out the problem then I remembered PartSelect & the info I got to fix the dishwasher. The info given for the dryer pointed to 2 main problems for no heat, tested them with the Ohm meter & ordered the part. We have a dryer again !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from glen head, NY
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
flame out
easy as pie !
Was this instruction helpful to you?
Thank you for voting!
Gas would come on initially then stop, no heat
This turned out to be easier than I thought. I opened the access door on the front of the dryer after unplugging the dryer and turning off the gas. I reached in just inside the door with a short-handled phillips head screwdriver and removed the two screws holding the two coils in place. The screws were pretty tight and a bit difficult to get loose but after serveral attempts they finally broke loose. Once I removed the plate that covered the two coils they just slipped right off, much easier than I thought. I removed the electrical connections then attached the wires to the new coils and slipped them back on their respective pins. I reattached the "cover", then plugged the dryer back in and turned the gas on and started it up. The flame fired right up, much stronger than before I replaced the coils and of course the flame stayed on. Problem solved. Repair was really pretty simple with the diagnosis being the biggest problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Mantua, NJ
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The dryer was not staying hot through the entire drying cycle.
Opened the top, removed the front panel. Supported the drum with my foot while I replaced the coils. I used a very short screwdriver so I would not have to remove the drum.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Weatogue, CT
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Gas dryer no / inconsistent heat
The hard part of the repair was the diagnosis. I'd take the front off the dryer, start it up, and the flame would fire up. I'd put it all together, start it, hear the flame start, leave, and it would still be running 4 hours later with the clothes wet. Discovered that one of the gas valve coils would work cool and show connectivity, but would stop working shortly after starting. To check the flame and remove the front, remove the door - 1 phillips screw in each hinge, then jiggle up and down pulling away from the dryer. Then, two screws on the opposite side. Facing the opening, grasp front and pull toward you to swing it down. You can temporarily put the door back with the front off while you start it to watch the flame cycle. On regular heat, the flame will run pretty much continuously - in my case, it would start, run for about 1 minute then stop. I assumed it was cycling, but it really runs longer than that. Coil replacement was easy - unplug the dryer, pry off the electrical connectors, remove the two screws on the left which hold the retainer containing the coils Then pull the coils straight up and replace with new ones. The one with three connectors is in front; the one with two connectors in the back. There are plastic tabs on the coils which fit into holes on the retainer. Reassemble in reverse order. To confirm diagnosis, you can use an ohmmeter to check continuity of the coils. The front coil has continuity between the center connector and each of the side connectors. The back coil has continuity between the two connectors. If you're not getting a reading at 1k ohms, it's probably an open coil and needs replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from College Station, TX
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
not getting hot
Checked the resistor to confirm it was good. Removed the two screws that are accessible after you pull the lint screen out. Use puddy knife to release the two plastic clips that hold the top on. The top will pop up like car hood. You have to pull up on it with steady pressure. I used a plastic puddy knife to prevent scratching anything. Prop top up so it does not fall back down and strike your head or fingers. On each side inside the housing there is a sheet metal screw that holds the front of the dryer on. Before you remove them unplug the door switch wire. As you get these off you will notice that the whole front is loose and the drum looks like it will fall out. It may if you mess with it. Gently tip the front away from the dryer housing and drum assembly. After the front is out about 5 inches pull up and the bottom can be moved away out of the small hook clips. Set it aside. The burner assembly is on the lower left. The coils are there remove the sheet metal screws and lift it up. Remove them one at a time. Notice the small locate pin and position the coil in the same orientation assemble in reverse. The door is tricky to get back on. Don't forget to unplug before doing any work. This can be done without disconnecting the gas service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- angela from schiller pk., IL
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Gas not staying on.
Unplug electric, open top, take off front, with a small Phillips screw driver remove two screws securing the coils, remove one coil at a time, unplug and replace with new coil, secure with metal bracket and reinstall front and top and your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald B from Milwaukee, WI
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dryer would heat on and off clothes not drying completely
Undo 2 screws take units out, clean a little, install new parts and screw down, done, great site !!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Madisonville, KY
- Parts Used:
- 279834
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The ignitor would lite, but no gas from the valve, then ignitor would shut off
It was a fairly simple repair to perform with the dryer in place. I simply opened the bottom/front access panel to start, the door removes if you pull up after opening. Then I disconnected the two and three wire connector to the two coils. Next I removed the bracket screws that fasten the coils to the valve assembly. This was a little difficult with the screw closest, because of the small clearance and #1 sized phillips(stubby would work well.) The rear screw I managed to remove by using both a small flathead screwdriver(hex shaped shaft) and an adjustable cresent wrench. At this point, it was a simple matter of installing the new coils and the bracket, and then reconnecting the two plugs. It almost made me want to do laundry.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Newfane, NY
- Parts Used:
- 279834
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Dryer was not firing consistently
Parts came as ordered and in really good time. The valves were very easy to install, just a matter of removing lower housing and the two screws holding in the old valves. The plug and play, no calibration needed and the dryer works like new. Very easy fix and the instructional videos were very helpful. Saved a lot of money doing it myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donald from anchorage, AK
- Parts Used:
- 279834
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dryer heats up for seconds and stat cold
open the back pannel and use multimeter to check the wirings and everything checks ok. open the bottom front panel of the dryer and turn the dryer on. the igniter works and the flame came out for seconds and dies off. the igniter keep coming on, but it seems that the gas was not coming out. i checked the gas line valve and it was open. i had a good idea it wasn't the wiring or the gas line, it must be the coil-valve,(safety coil), that letting the gas flow. i order the parts, it came sooner, which is good, and it took me less than 10 minutes to install, and i only use a philip screw driver. i thank you for sending me the right part in short period of time.
Was this instruction helpful to you?
Thank you for voting!