Models > YWED5050LW1 > Instructions

YWED5050LW1 Whirlpool Dryer - Instructions

Jump to:

All Instructions for the YWED5050LW1
121 - 135 of 254
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
David from Jamestown, RI
Parts Used:
4392065
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Drum stopped turning
Using a stiff putty knife I depressed the clips that hold the top down. I loosened the screws at the lower edge of the front panel and removed the two 5/16 head screws that hold the front on. I unplugged the door switch and lifted the front off the lower screws. I removed the drum and the broken belt. I replaced the rear rollers after applying some dry lube to the shafts and replaced the tension spring and rolled. I replaced the drum and belt and attached the belt to the small pulley on the motor. Then checked the rear gasket felt and reinstalled the front cover and the top.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Snowmass, CO
Parts Used:
4392065
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set
Thumping sounds
Kit was easy to install and after making sure the drum gaskets were set right the noises ended.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cindy from Buhl, ID
Parts Used:
4392065
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
the dryer was making very loud noises when tumbeling
Watching the video from Parts Select for replacing the rollers showed us all we needed to easily replace the wheels as well as the Pulley and belt. It made a gigantic different in the noise and efficiency of the dryer. One of the Wheels was actually 3/4 gone, worn away. Hopefully, this repair will extend the life of an already old dryer. Thanks for the videos that made the repair a 'piece of cake'.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bill from Greeley, PA
Parts Used:
4392065
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Wrench (Adjustable), Wrench set
broken belt
it was easy all the parts were the exact replacement
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Libertyville, IL
Parts Used:
4392065
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
LOUD squeling from Dryer
Belt was worn, rollers were sticking, idler worn out. Ordered a kit to care for these issues, as usual the reapirs took almost no time. Dryer became a bit quieter for a first load, second load the motor siezed. I priced rebuilding most of the machine and determined replacement was due.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert G from Dansville, NY
Parts Used:
4392065
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
drum not rotating
Pull lint screen, remove two phillips screws,pry top front up and hinge back,remove two screws at top inside, unplug door switch, lift front and remove, remove drum. Read instructions,install new parts, reverse above dis-assembly, happy dying.
Was this instruction helpful to you?
Thank you for voting!
Customer:
FLOR from Jersey City, NJ
Parts Used:
4392065
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Socket set
broken belt and roller
Replaced Broken Belt and roller
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Wood-Ridge, NJ
Parts Used:
4392065
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
noisy
Following the step by step instructions it took longer to clean the old lint out of the bottom of the dryer than to perform the entire repair.The maintenance kit came complete with every moving part(except the motor and drum)and now it runs very quietly.I am all thumbs when it comes to tools but this was very simple.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from Pasadena, TX
Parts Used:
4392065
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Load whinning sound
I reviewed the instruction video. Excellant video. exactly like my dryer. Just followed the instructions. I did put a shoe under the drum for easier installation of belt onto idler pulley. I vacuumed and cleaned inside. Really not that dirty.Excellant web site and video instructions. Wish I had done the repair sooner. Also God Bless the residents of OK city, Moore, and ElReno.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carolyn from Sonora, CA
Parts Used:
W10470674
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Needed to vent the dryer to the left side
The kit turned out to be missing a 7.40" 4" diameter vent that was needed so ending having to get my plumber to use what was there with a "cut and paste" job - took him over an hour. He did say that had the right piece been there, it would have been easy.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lawrence from Cape Coral, FL
Parts Used:
4392065
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Dryer became EXTREMELY noisy
Kit arrived with all the parts required and with detailed instructions. LOL... the very specialized tool you will need to dis-assemble the dryer? A PUTTY KNIFE. All in all, aside from the top of the dryer slamming shut without warning and scaring the pants off me, this was a relatively easy repair from a technical level. Only real difficult thing was removing and then restoring the drum and that was more due to clearance than actually being difficult. Make sure once you're finished to LEVEL THE DRYER. That makes a HUGE difference!!!!!
Was this instruction helpful to you?
Thank you for voting!
Customer:
kimberly from petaluma, CA
Parts Used:
4392065
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set, Wrench (Adjustable)
broken dryer belt
Everyone said changing a dryer belt was a piece of cake.They did not tell the truth it is a difficult job. I am a 52 year old female and I had a problem. You have to take the whole drum out. I finally completed the job but i had to prop the drum up with blocks so I could screw in the front panel. I think for those who want to change the belt I would go smoother with two people so the can hold things in place while the other one screws the panels back. I also think taking the dryer door off make the front panel a lot more easier to put in palce.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brian from clermont, FL
Parts Used:
4392065
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Squeezing when dryer runs
Followed instructions that came with part.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Victoria from Sewell, NJ
Parts Used:
8212450A
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
I just needed to replace the rack in my dryer
This did not require a "repair", just a replacement. I want to say that the response time and ease of ordering were very good. I would not hesitate to use PartSelect again when needed. Thank you!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Harlon from Browns Summit, NC
Parts Used:
W10470674
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Needed to vent to side due to space requirements
Upon receipt of the new vent kit, I removed the dryer from its location and took it in to the garage. This facilitated a roomier work space. The directions were easy to follow and the work to be performed was very easy in this setting.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the YWED5050LW1
121 - 135 of 254