YWED5050LW1 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from North Attleboro, MA
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Tumbler drive belt was slipping which made grey dust coat inside of dryer
Installed new belt and cleaned dust and wiped out inside of drum with Fantastic and clean sponge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from Middletown, NY
- Parts Used:
- W10869845
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Washer Would Drain But Not Spin
Removed rear cover (6 screws) unpluged harness from motor control and removed same. Replaced motor control reinstalled harness. Replaced rear cover. Parts used motor control board.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wendy from bush, LA
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer Came On & Made Alot Of Noise
Took off the front of & lifted the top up. Pulled the drum out & replaced the two wheels that turn the drum, replaced the belt & replaced the pully wheel that turns the belt & dryer motor & put back together. The dryer now runs like a new one. Has no noise when running.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Oscar from Mamaroneck, NY
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer drum didn't turn
Found a DIY video clip on YouTube...Ordered the parts...I only needed a replacement belt but PartSelect had an upgrade kit that included not only the belt and rear drum support wheels, but also the tensioner arm with a WHEEL instead of just the flat metal belt guide ( which I believe lead to the belt wearing out in the first place) All the parts fit perfectly and now it's better than new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- valerie from mishawaka, IN
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
belt broke
I watched the video online in the order section. then just did it after we received the repair kit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Cheswick, PA
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Support Roller Worn Out
Followed instructions supplied ( very easy)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Westhope, ND
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Drum does not rotate
Diagnose the problem. Is it the motor ? Is it the belt ? Order the correct repair kit, use name brand parts to ensure reliability. READ THE SUPPLIED DIRECTIONS. You can use a small wood shim or wedge at the top front corners to open the top . Use a 5/16" socket to remove the 2 screws at the top outside corners. Lift the front panel straight up, supporting the drum as you lift it off. Remove the drum, taking it straight out the front. Install the new drum rollers, install the idler, and then the belt around the drum. Install the drum on the rear rollers, make sure the seal is not folded under. Push the drum back against the seal flange, support the front of the drum with your right (or left ) hand, and sit the front panel on the lower pins, and gently push the front panel to the sidewalls. Feed the belt through the idler and around the motor pulley. This job is easily performed in about 20 minutes. Clean the interior while replacing the belt/idler and drum rollers. With the top lifted, after assembly, test run the dryer to make sure there are no "funny noises" after the repair. Watch especially for the white rub strips on the front edge of the drum. They tend to fold over when attaching the front panel. Job done !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from N Chelmsford, MA
- Parts Used:
- 4392065
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
drumbelt broken
Used a ropeasround the dyer drum to simulate thebelt to peload the idler This allowed me to get the belt over the motor shaft without the idler sping tenion causing the idler to jump at random timesafer I strted using the rope the belt was on in 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from DELRAY BEACH, FL
- Parts Used:
- 4392065
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken Dryer Belt
Ordered entire Maintenance kit - good call because it was the tensioner pulley that failed and cut the belt. To replace, had to raise the top (2 screws in lint screen slot)and pull the entire front off (2 screws - 1/ea on top inner edge of front door panel then lift it up and out) Replaced both rollers, then used the parts kit shipping box to prop up the front of the drum while installing the belt and tensioner pully. Re-assembled in reverse order, works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Natale from Brooklyn, NY
- Parts Used:
- 4392065
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Dryer making squealing noise
Followed the directions on the web site. made a hook out of a wire hanger to hold the drum in place (hook from the back frame to the front of the drum) while I set the belt tensioner in place. removed the hook and the rest was easy.Works Great!!! like a new machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bradley from Mineral Point, MO
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Very loud
Had to order idler lever and wheel as the one in the kit would not work. Best to buy part specific for your dryer. Repair was easy, just watch repair video. Sounds like new dryer again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dustin from Martinsville, IN
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Rollers squeaking on dryer
Watched a brief video on YouTube and followed step by step. Real easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Bettendorf, IA
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The dryer sounded like a herd of buffalos running by.
I needed to replace our drum support rollers - one was completely worn out and wobbling (the buffalo herd noise) the other wasn't too bad, but for an older dryer(15+ years) I figured it was time to replace both wheels. I ordered the maintenance kit that also included the Idler Pulley and drum belt. I spent most of my time with the vacuum since there was a lot of dust accumulated inside the dryer. (I recoverd $1.83 in coins!) The instructions that came with the kit were very helpful for this repair. Plus, there were some online videos that heled as well. Once I had everything apart I noticed the plastic bearing ring on the drum's front was nearly worn out so I quickly ordered this from PartSelect and it arrived quicly in two days - this took only 10 minutes to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Sayrevlle, NJ
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Drum not rotating
Broken belt, but went with the mainentance kit since it was going to be all apart anyway. Found the job easy to do and the new belt idler was a big improvement over the old style. /also came with instructions. Good for another 5-10 years.
Was this instruction helpful to you?
Thank you for voting!