CED7011LW1 Whirlpool Dryer - Instructions

I followed the video provided by ‘Partselect’; although it was not the exact model it was close enough to get the job done with high confidence.

pulled dryer away from wall took screws out of lint screen lift top removed 2 screws one on each side of front at top and removed front panel. pulled belt off drum removed drum rollers tension pulley and while i was at it pulled back cover off of heating element and blower blew everything out with air hose did a total cleaning installed everything in reverse. i was amazed how fast the parts came the dryer was only down 2 days and it runs like new even if it is 20 years old i highly recommend parts slect and i will use them in the future

I changed the belt, tension pully and rollers. Runs like new now. I also took the opportunity to clean it out real good while I had it apart.

I opened the top and front of the dryer. 1st I pulled out the drum and cleaned up the lint and mess from the busted support roller. Next it was a matter of looking at the enclosed drawing and instructions. I could not believe it was that easy.

We had to pop open the top. Unscrew front of dryer from sides. Disconnecting the wires was a bit more difficult than expected. We had to use a tiny screwdriver to slide into the sides of the white wire connector on each side before pulling apart. Front drum falls when front of dryer is removed. It took two of us to reassemble - one to hold the drum while the other put the front on. Our problem turned out to be one wheel. We replaced both wheels and saved the rest of the parts. Hums along just fine.

Replacement handle snapped right back in place. Took about 2 seconds.

followed simple directions and it took 1 minute! Lime up with the hole and gently push, it clipped in immediately! You are a great place to go to for repairs!!!

The part arrived in the mail. I used a pair of kitchen scissors to open the package. I removed the part from the plastic bag, and snapped it into place on the front of the dryer. Total time: 15 seconds.

I wish all my repairs were this easy.

Followed the directions and just snapped the new handle in place

The drying rack sent matched the dimples,9.5 inches apart, but it was an inch and a half too long. The rack sent was 21 inches, I need a rack that is 19.5 inches long. So I returned it. At TWICE the cost of the rack itself. Still in search of a rack that will fit my dryer

removed and replaced door handle no tools required

I ordered a Maytag side vent kit, #12002641, I received a part #2003961.The kit had 2 vent pipes that were about 4" x 24" and an 4" Ell. $105.00. Both vent pipes were too long. I was desperate to get my new dryer installed, so I took the vent pipes to my cutoff saw and made the fit. I then found the right part PS2003058, on your website at a price of $36.22.

I use the manentance kit that was not the problem. I end buying the drive motor and that was it. I was happy with the service I got from part select, overnight mail what more could I ask for? I am also glad I replace everthing with mainentance kit. Thank you for your help john degnan

This was super simple - even I could do it! I followed the 3-step instructions which basically described how to hold the new handle and pushed it into the holes in the door. Less than 30 seconds and no tools.

Took the two screws holding the lint trap to top. Used a putty knife to loose the clips holding the top of the dryer up so it could be hindged up for access. Used a nut driver to remove the four screws hold the front door on. Removed the lower dust panel, just clips holding in on. Pull the dryer drum out along with the broken belt and old belt tensioner. Took shop vac and cleaned lint and removed about $2.00 of loose change from the base. Installed the new drum supper wheels. Held belt around drum to put back in. Looped the belt through tensioner and around motor drive pulley as shown in instructions. Put front door on only to find the felt around the door had slipped making the drum hard to turn. Pulled the door back off and laid the dryer on it's back before putting the door back on , so you can run your hand around the door to make sure the felt go inside the drum. Put the four screws back in the door panel before uprighting the dryer. Sucess the drum turned freely. Put other remaining panel and srews in lint trap . Hook the dryer back up to vent, power and gas, and turned on the dryer. Runs like new!