7MMGDC300DW3 Whirlpool Dryer - Instructions

ordered a replacement handle - installed it myswelf

I opened the package with my new handle in it that I got from PartSelect, and snapped it right in place. No tools needed, took only seconds!

Just popped it into place. Was very easy. Took less than 5 minutes.

Very simple remove door pull off old seal, apply small amount of adhesive around seal seat. Install seal to door let cure for several hours over night is best

Called parts select and explained my problem with representive and was able to order a new timer which included the selector stem. Received the correct part in a couple of days. Very quick! Removed back plate of the top part of dryer. Removed 2 screws holding timer and removed old timer. Installed new timer and reterminated wiring to back of new timer. Replaced back plate on dryer. Dryer was ready to go. Minimal down time!

Very simple. Unplugged. removed top back panel. Removed two screws from timer. Removed wire one at a time replacing them in new timer. Then reassembled

Lint can build up inside the dryer, and can cause a fire in EXTREME cases. If your model has a back panel that exposes the entire chute, this job is much easier. Unscrew the chute from the machine to remove it. Inspect and clean all the lint out, especially the bottom, next to the fan blower. The other version machine has a panel at the top that is welded on. Remove the two screws at the top corner of the rear bulkhead, where the chute is. Gently pull this inner panel away to free the top of the chute from the rear top panel. Then pull the chute down and out. Follow the reverse to complete the job.

Removed rear cover (6 screws) unpluged harness from motor control and removed same. Replaced motor control reinstalled harness. Replaced rear cover. Parts used motor control board.

I just followed the instructions provided, after taking a long look as to whether it really applied to our dryer. Just take your time and install the unit as you removed it. We removed the unit by first removing gas line, then two screws on the side and it was out. Put on stopper, followed by switching out the orfice.

Followed Directions included with Kit. Directions were right on. Have done other Range and Drier conversions in the past.

I pulled thee dryer out from the wall, shut off the gas & disconnected the gas line & the air vent, I then removed the fasteners from the upper end of the lint chute assembly (accessible from the top of the machine). I then tipped the machine over on to its front side making the back fully accessible. After removing the back cover, I removed the remaining fasteners holding the lint chute assembly in place & removed the part. I then removed the assembly only to find that the seals were not included in the package even though I had specifically asked about the seal when I called in & place my order. The response to my question was " seals are included that is why it is called an assembly." The end result was that I had to use alternate material & fabricate my own seals in order to complete the installation. As a result a repair which should have taken no more that 30 minutes, took over two hours.

Had no definative directions so kind of had to play it by ear. once I got the top and front off the directions that came with the part were spot on. My biggest problem was I guess I was a little over agressive with the drum and I pulled the tension pulley off the bottom. I had to drill a hole and bolt it back down because I couldnt get the little flanges to bend over enough to hold it. It works now but I havent done a load of clothes yet to make sure it will stay together

Initially bought a few parts based on past experience without testing first....my mistake. After testing and purchasing the correct parts the dryer works fine. This is by far the best DIY web site I've ever used and recommend it highly. If you can follow online instructions, this is the way to go....it saves $$$ on service calls.

This did not require a "repair", just a replacement. I want to say that the response time and ease of ordering were very good. I would not hesitate to use PartSelect again when needed. Thank you!

Ordered the part, called a friend that is a LP worker. He came over and in less than 15 mins had the new orface and regulator plunger installed and another 10 mins to install new flex pipe and shut off valve and it works great. It was really easy I watched him do it and could of done it myself if I did not have a friend that could do it.