DG170AXW3 Westinghouse Dryer - Instructions

First I took the drum out of the dryer. This was an easy tear down. I had to remember 2 wires, and a belt assembly ( 2 pullies ). I removed 3 screws inside the drum to release the bearing assembly from the back. Then I went to the dryer chasis and removed the mounting bracket by removing 2 screws. I simply replaced the mounting bracket with the new one. This required having to use a magnet to hold a small ball bearing in place while I worked the rest of the pieces in position.I greased it up and went back to the drum. I replaced the old bearing assembly with the new one. Easy. I took the time to shop-vac the inside of the dryer. There was a lot of loose lint, candy rappers, coins, etc. Finally, I put it back together. Unfortunately, this is the forth (4th) time I've had to do this. It's cheaper than buying a new dryer. Now, I've got to fix the washer.

Took a putty knife and released top clips. Tipped top back , and took out 4 screws holding front cover in place. Lifted out drum, replaced bearing plate. Removed 2 screws and replaced back panel bearing. Placed drum back in place, installed front panel, snapped top back in place and job was done. Very easy. Took about one hour.

Remove top cover and front and remove drum and install a new bearing kit and new belt.

Followed video instructions, easy installation. Unfortunately it didn't fix the problem. Plan to take back off and check belt, etc before ordering another part.

Read your article on possible repairs for different symptoms and after dis assembling and cleaning certain parts took a chance on the flame sensor, which turned out to be the culprit. Your help was a valuable tool in the repair process ! What would be the bee's knee's would be the resistance reading on the sensors that monitor the system for a more accurate diagnostic approach. But none the less you definitely aided in the repair of my propane gas dryer. Thank you very much ! And by the way the 3-4 day wait for the part was well worth the half price I paid versus our small town repair facility, Thanx again

lacked instructions. Internet yielded a simple paragraph. Scored real bonus when we discovered the lint build up past the internal filter was approaching catastropic level. Replaced the exhaust tube (plastic) with rigid metal and resolved to disassemble and clean dryer on 2 year cycle in future. Kit just isn't complete without detailed instructions. Parts were complete and sufficient. Local codes have eliminated the plactic exhaust tube. Recommend that all old installs refit to rigid or semirigid before the fire happens!

First removed the top of the dryer, then the front of the dryer. Took the plate off the back left of the dryer to disengage the belt off the pulley.
Took the three screws out that hold the drum in place, of course the third screw stripped and had to use a screw remover, which didn't work, but the adjustable pliers did so then lifted the drum out of the plastic reservoir in which the bearing laid. Next unscrewed the two bolts holding the plastic reservoir which also loosened the small metal piece on the back of the dryer where a small bearing is located. Put the new parts in, but instead of putting the larger bearing that fits in the plastic reservoir, I decided to put it on the drum first and guide it into the reservoir all at once, this worked well . Prior to that I put the new plastic piece on the inside and taped it there while holding that piece put the small metal piece with the small bearing on the back of the dryer. I'm sure it is alot easier with two people doing this part, but it worked and I didn't lose the small bearing. Next put the front of the dryer back on and then put the belt back on the pulley, then the top.
It definitely helped immensely to read how someone did this, just follow the instructions given and there you go, no more annoying squeak and also a feeling of accomplishment and thanks to the person who wrote the story on how to do this job, appreciate it.

remove the top and front of the dryer, then removed the idler assembly. This enabled me to rimove the belt form the drum and replace it and the idler assembly. Not difficult at all.

I first diagnosed the problem using a Google search. Amazing how many hits I got and after reading a few was pretty certain what the cause was and what parts I probably needed to make the repair.
Some of the articles I read had links or mentioned PartSelect, so I searched for my model # and found the parts I would probably need. Knowing that I could probably get the parts I needed I disassembled the dryer (pretty easy really) and removed the old suspect part. It was devoid of lubricant and the bearing and ball showed some wear so I ordered the Bearing Assembly suggested by PartSelect (the illustrations looked just like my old parts). I left the dryer disassembled while I waited for the part, figuring it would take a week or so to arrive.
Much to my surprise, the part arrived three days later and after cleaning the dryer innards of all collected lint I put it all back together in 30 minutes.
So for a little research, a $30 part, and about an hour of my time, I have a clean and quiet operating dryer. I see no reason I can't get another 10 or so years out of it.
I consider myself a reasonably handy guy but had never worked on a dryer before. I'll be unlikely to ever call a repairman without first doing some investigation and seeing if the parts are available. With the internet and PartSelect I think I could take on a lot of other repairs I'm not familiar with. Thanks for a great outcome this time around.
Kevin

Popped the topped using a putty knife to free two clips in front. Remove two screws now accessible on the front inside panel. Remove two wires to door switch. Remove rear access door, two screws. Remove belt from tensioner in rear and remember or take picture of how it goes. Lift barrel slightly and pivot front panel out of the way. Lift barrel free from ball socket in rear. Lift out from front panel area. R & R kit and put back in reverse order.

After watching the video that explained and showed how to replace the bearing assembly, installation was a breeze. Great company to do business with. Ordered the part and had it in two days, and the dryer was working again asap. Thanks PartSelect
PS this dryer is 23 years old.

removed front of drier , removed rear access panel, replaced the belt. reinstalled front of drier and rear access panel

first and foremost, watching video on replacement/repair was key to success.furthermore, i ordered part one day and was at my doorstep the following day. the installation process took approximately half of an hour which included vaccuuming cabinet of lint.

Replace the Drum Bearing and Shaft

unbolted one bolt and replaced old unit with new unit....took only a few minutes. Part was supposed to arrive in 3 days, but arrived next day....thanks very much!