DE170ADF2 Westinghouse Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Niel from Howell, NJ
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
dryer started to squeal when started
I watched the repair video on how to replace the rear bearing and ordered the parts.The video was 100% correct and showed the repair step by step I didnt even need to replay it.The repair went as expected and no left oover parts. My dryer runs smooth and quiet, My wife loves her quiet dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Centennial, CO
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Loud squeeking and vibration of the dryer drum.
I followed the directions sent by you step for step and the rpair was done in no time at all. Had a little trouble with the roller ball installation but figured out how to install it after a couple of tries. Repair was done with minimal use of standard houshold tools.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathleen from Port Orchard, WA
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
dryer squeaked
It was easy, I handed the part to my husband and he did it!!!!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Hermitage, TN
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
began as intermittent squeal then became more louder and frequent
removed top-removed front-removed belt-removed drum (I didn't know how the drum came out WITH the bearing so I unscrewed the 3 middle screws on the back of the drum which released it from the bearing)- removed the bearing-that was when I knew what to order. installed the bearing on the drum before assembling all in reverse order. I wasn't sure how much grease to use so I used about 1/3 of it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sam from prattville, AL
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
loud noise at back of dryer
i watched the video that is furnished at parts select, it was very useful in doing this repair. i would strongly recommend watching this as i did install the ground bearing wrong to start with,and restringing the drum belt is something you have to feel as your installing it back in place so the video is useful for that as well. my repair was on a front load dryer made by Frigidaire,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vern from Sedalia, MO
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
squealing, very noisy dryer!
I used the video, and it helped me a lot! I got the drum out, installed the new bearing, greased the new shaft and the receptacle, then I reassembled. When I tested it, mine was still very noisy, so I removed the drum once more and cleaned/added some grease on the tensioner bearing. This was the cause of the noise in my case, but the bearing & housing were nearly shot, so something would have given out very soon. I would suggest to grease the tensioner the first time to save time and effort. (And save some of the grease for the tensioner pulley). SAFETY TIP: there was also a ton of lint that got trapped inside the unit!!! Clean your dryer once per year to prevent it becoming a fire trap!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gordon from creve coeur, IL
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
banging noise
followed vidio instruction which made it easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernest from Stockholm, NJ
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Loud squealing noise until dryer heated up - then quiet
purchased bearing kit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from New London, NC
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Dryer was making a noise like scraching a black board.
The repair went very well.The biggest problem was the spring on the tension roller when putting back together.But it just takes a little bit of patients and it was fine.Works great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from Weirton, WV
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
loud squeek
followed the Video instruction which were provided. Dryer works like brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delbert from Grass Valley, CA
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
A loud squeeling sound
Had the macnine apart before ordering the Bearing Assembly. Reading other comments convinced me to order the Bearing Assembly. Parts were shipped very quickly after ordering and following the instructions on the web site things went back together easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Raven, VA
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Dryer making scrubbing noise while running
This is a front load dryer. First unbolt top cover of dryer. Then unbolt screws and connections to control panel. Next unbolt all screws holding dryer door and front bottom panel. Next take belt off of drum and slide out drum from the front. From inside of drum remove 3 screws and remove bearing then put new bearing on and bolt up the same way you take old one off. Using an 8mm socket or wrench remove plastic bearing cage located at rear of dryer. When unbolting there is a retaining clip and small steel ball to be removed from back of dryer. Replace this the same way you take it off. He sure to grease the bearing cage then replace everything back from putting the drum in first to your last step bolting on top cover of dryer. Hope this helps anyone doing this repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Hernando, MS
- Parts Used:
- 5366021400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door Would Not Close
Inserted clasp in frame of door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Bainbridge, PA
- Parts Used:
- 5366021400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer door would not stay shut.
The other door latch broke and fell out. I simply pushed the New Door Latch in the hole, and it snapped into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacy from East Nassau, NY
- Parts Used:
- 5366021400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Catch broke
My son kept slamming the door wrong and eventually the catch broke and two and feel out. My husband is the handy man of the family, but has been so busy that I was just duck tapping the door close. Finally, I decided to see if I could look up the part. Found it on here, ordered it, and replaced it all myself! Proud mother right here! Very easy. Works great.
Was this instruction helpful to you?
Thank you for voting!