EG1120 Speed Queen Dryer - Instructions

once I found where the heat element was, it took me a few mintues to remove the bad one and replace it with the new one that came before the due date. very good instruction in kit. Be sure and leave the old one hooked up until the new unit comes in so you can do a easy exchange of the wiring.

I dismantled the dryer and replaced the thermostat and the heating element. The online videos are excellent. Thanks

removed the lower cover, tipped the dryer on its back for easier access, unscrewed the 2 mounting screws removed the heating element, installed the thermostat and and high tempt relay on new one replaced the wires reinstalled the new element, very simple

You have to take apart the whole dryer to get to the belt.Nut driver with cordless drill make it go so much faster.Unplug dry, take apart dryer and replace with olr belt with new belt.Takes about 20 minutes to do.plus I took off the two guide wheels on back of cabinet and greased everything.Works like brand new.I had a repair guy tell me I needed a new motor.If you can spin the drum by hand replace belt first.

My problem was that my AMANA dryer would not heat. The site suggested testing the two thermostats so I opened the dryer but didn’t follow the instructions in the video tutorial on the site since my AMANA is different. I used a nut driver and needle-nosed pliers for the whole job. Here’s what I did:

1. Unplugged the dryer.

2. Disconnected the exhaust pipe at the dryer.

3. Pulled dryer away from back wall about two feet.

4. Removed the two bottom panel screws (floor level) and removed panel.

5. Removed the two door panel screws and removed door panel by pulling out at the bottom until the two spring clips released from the top panel.

6. Noted the colors of the wires going to the door switch and removed (green, black and white from left to right).

7. Noted the colors of the wires going to the lamp and removed (bottom - black and top - red.)

8. Removed the two top panel screws, lifted up the top panel and leaned it against a support.

9. Removed the four bulkhead screws and carefully lifted up and removed the bulkhead being sure to support the drum. Took note of the belt path around the motor and idler pulleys.

10. Reached under the drum and took the belt off the idler pulley and motor drive pulley.

11. Used the belt to lift and remove the drum through the front opening.

I noticed that the internal vent pipe had become disconnected (which probably caused internal overheating) so I fixed that.

I then removed the wires to the thermostats and tested both for continuity. The limit thermostat was bad. I also saw that the belt was becoming cracked. I ordered a new limit thermostat and belt.

Installation of the new parts was a snap. I removed the old thermostat with the nut driver and replaced with the new one and pushed the wire connectors back on. Replacing the belt was a little trickier but not a problem. (Be sure to route the new belt correctly as noted on Step 9 and place ribbed surface next to drum.)

I closed up the dryer by reversing the opening steps.

as described in video. Very well done. Thank you

Loosened the screws, took out the old one. It shorted out to back. Inserted the new one attached wires, Installed screws and it worked

Determined no air flow or heat through system even though dryer spun and timer worked. Ouside vent dispelled no air. Opened dryer panel.
Blower wheel/fan broken off from shaft. Googled appliance parts ... found ... Partselect .... keyed in mfg, model number ... schematics available ... found part ... ordered ... received in two days ... installed ... reassembled. Working fine ! $ 30.00 compared to buying new dryer ! This was a refreshing and rewarding repair. If it could always be this smooth !!! Great resource ... PARTSELECT !

The first time, I inserted the belt the wrong way. The drum turns a little bit then stops. The manufacturer does not give any instructions or drawings on their website on that particular model, only drawing of parts.I called the technical support department and they told me to call different telephone numbers in my area and repair technicians. Still no schematic and instructions.
The solution: I took the broken belt, put around the drum, measured it, the remaining slack, did some trial and error around the motor axle and the pulley.
Placed a 2 X 4 piece of wood to hold the tension of the pulley. With the belt around the drum, carefully inserted the drum downward. placed the belt starting from the left side of the drum to the bottom of the motor axle, around it then to the bottom of the tension pulley, then towards the right side of the drum.
Lift the drum to its proper position, horizontal. Remove the piece of wood. Turn the drum manually so it moves freely. check the belt moving around the axle and the pulley. Install back the panels and screws tightened. Test and observe a few drying runs.

This would be an easy job, if I were to do it again.

I needed to download a manual only to get ACCESS to the machine. Removing the outside lag bolts did NOT provide access.

They had hidden clips that were ENTIRELY invisible from the outside. I believe this was done deliberately, to prevent those who don't know the specifics about this machine from gaining access.

It's an easy job, once you know the idiosyncracies of the construction of the machine. It's a major pain in the ass if you don't, even if you are used to replacing belts in other dryers.

Having done it once, the next time I could do it in under 20% of the time it took me the first time.

Basically, Followed the instructions in the Video for Belt replacement. I found out however that the Tensioner was also broken aand needed replacement, and this required the snap wring pliers. also spindle on motor was stripped and had to use "lockTite" to repair that. Overall was far better "doining it myself" than paying for repai service which would have cost several hundred $ in costs. This increased my confidence level to know that as long as parts are available I will always be able to repair this appliance!

remove front panel ,remove top panel,lift drum,slide new belt on to drive motor then idler pulley then put belt over the drum.reassemble in reverse , front panel first

Removed 2 screws on the bottom of front panel of dryer & pulled it off. Next I got down & looked to the back & bottom inside of the dryer. I spyed the heating element,I pulled off the two wires from the thermostats[ orange & black. I removed two screws from the heating element plate & dropped it down & removed it from the dryer. Reverse procedure to reinstall. Will see if we can get another 10 years service out of it.

Fairly easy to repair once I figured out how to get it apart. The amazing part of this was searching the web for the part. I found PartSelect, ordered it at about 2pm Eastern time and the part arrived the next day! I will definitely use this service again.

Leaned machine back and put blocking under machine to elevate. Removed two screws from front of bottom panel. Lift panel out and set aside. Next remove two bottom screws from door frame. Pull bottom of frame out and up to release. Remove wire clips from door light and switch. Set door frame aside. Inside drum, take three phillips head screws out, that hold filter frame in, remove filter frame. Next remove four front screws on drum alignment face plate. Set aside. Grasp drum and pull forward, off back guide rollers. Drum will drop down a little, reach in around drum and slide belt off. Remember to look in under drum to see proper placement of belt aroun motor shaft and idler pulley. Replace new belt around drum with ribs against drum. Route belt around motor shaft pulley, pull idler pulley toward motor and place belt around pulley smooth top runs against pulley. Reinstall everything you removed. Connect wires to door.