ADE41FSS171TN01 Speed Queen Dryer - Instructions

Well, had I read more of the reviews on this website, I would have learned that my problem was the valve coils. Instead, I assumed it was the igniter, so I ordered and installed a new igniter to no avail. I was about to just go buy a new dryer at Home Depot and spend $600, but I had to try again so I read more reviews on this website and began measuring resistances across the valve coils and discovered I had a bad one. I ordered both just to be safe, and installed them and quickly enjoyed my first uninterrupted dryer cycle in over a year (for over a year, I had been stopping and restarting my dryer about 10 times for each cycle). So THANKS for this website and to all the home technicians who posted symptoms, resistances, and how-to-do-its to help me get this done. It was an empowering experience to fix this and have bookmarked this website for any future appliance fixes. It's a great website with all its schematics and postings.

As it turned out, the felt was only part of the problem. The guide bracket had been cut thru by the drum. This all started when a golf tee got stuck in the drum area. It took very little time to destroy the guide bracket. Dryer was built by Whirlpool. Parts are built to the bare minimum. These appliances are designed to break in a couple of years. There is no doubt about it. I installed the new guide brkt, glued the new felt on and put it all back together. The job is pretty straight forward but you need to be mechanically inclined.

Step by step, I removed the bottom front panel with a putty knife to compress the spring clamps, removed the inner lint trap, disconnected the door switch and springs and blower connection under the drum, removed the lint trap/ blower housing, remove nuts at bottom sides of door panel, lift top front of dryer (putty knife, spring clamps) to remove nuts at the top then removed the door panel. I then released the belt from the (spring) pulley and pulled the drum out. Pay attention to how the seals were put on! I removed the old seals and cleaned off the old adhesive with acetone and a steel scrubby( wear gloves when using acetone and when applying new adhesive, and work in a ventilated area!) Follow instructions for applying the adhesive for the seals. Put back together in reverse order. Repair successful!

I unplug the electric, close the gas valve, use the putty blade to prize up the top,unplug the electric horness, took the front door off, took the anker plate off the two coils, removed the wire from each coil,be careful not toget the wires mixed up one coil has two proms and the other has three proms after that u put everything back together the way u took it off!!

1. Unplugged from wall, turned off gas and opened top cover. 2. Removed two wire clips for door switch and unscrewed front cover (2 screws inside). 3. Removed front cover and moved to side. 4. Unplugged connectors from coils. 5. Unscrewed coil screws. 6. Replaced coils and tightened screws. 7. Replaced front cover, tightened screws and reinstalled wire clips. 8. Closed top cover, turned on gas and plugged in power. 9. Dryer fired right up and made heat.

Followed video on PartsSelect website, they made it real easy.

The front panel was taken out and the parts were replaced. After the replacement, the drying time went back to the original 30-40 minutes.

Gas valve coils need replacing I followed parts select.com video on YouTube and had no problem. It went exactly as the video followed parts select.com video on YouTube and had no problem. It went exactly as the videos showed!

When you open the door to the dryer there are 4 screws you need to remove (2 on each side) in order to remove the front panel. Once I removed the front panel I then turned the dryer on to see what was happening inside. The heating element was turning orange with a glow but the gas wasn't igniting. After looking on-line I figured my next option would be to replace both gas valve coils (one is 2 terminal & the other is 3 terminal). Once you have the new parts & are ready to install them unplug the dryer. All you need to do is first, unplug the 2 plastic sockets that feed the electricity to the coils (they have wires attached to them) unscrew the bracket that holds the 2 coils in place, pull the old coils out & put the new coils in, replug the electric plugs, re-attach the bracket that holds the coils into place, plug in the dryer & turn it on. Test it without the panel on so that you can see that the gas ignites. My husband was very happy when I told him I repaired the dryer - beats paying another repair man.

bought the new coil valves changed out new for old, presto dryer works now

This 10 year old dryer stopped heating. I knew a Maytag would have much more life left in it than that (even my Mom's lowly GE lasted more than 40 years!) so I was sure it could be fixed. Without doing any testing, I had just guessed that the glow bar was bad and replaced it. But that wasn't the problem - the old glow bar still had continuity as tested with my ohmmeter. So I dug in deeper and looked over the schematic posted on PartSelect's website. The glow bar would light up and then go out, but the gas valve never opened. After probing the two solenoid coils for voltage, I decided the primary solenoid was bad. This was confirmed when I took the connector off and checked with an ohmmeter (never do this with the wires connected!) and found no connection at all between the two terminals.
Ordering the new part from PartSelect was fast and easy and my part arrived in two days. The solenoid coil on this dryer can be removed from the gas valve without taking any gas lines apart - I don't know if they're all like that, but it's a great feature. The only hard thing is that there is no access door to inspect the flame like older gas dryers. You have to take the front panel off to watch it working, but that just involves the four screws around the door opening.
If your pre-Whirlpool Maytag dryer is giving you trouble, take heart! These are great machines that last long, are easy to fix, and parts are easier than ever to get with PartSelect!

First I unpluged the dryer,thenI removed the front of the dryer,spun it out of the way but did not detach the door wires.I then took the two skrews out of the braket that held the old coils,unpluged both coils, I replaced both as I did not have the means to find which one was bad.Besides, I did not want to visit the insides of the dryer for another five years. This was a snap and the parts were perfect and arrived timely.

and the problem wsa solve

Unplugged dryer, and removed vent hose. Tilted dryer back, unscrewed 2 screws on lower front panel. Removed 2 screws on coil holder (needed a short screwdriver). Unhooked wiring harnesses from coils, and removed coils. everything in reverse for installation.

Used your sites diagnostic questions to determine that the gas coils were the most likely cause for no gas ignition. Ordered parts. Followed general directions from your web site....very helpful. Disconnected electrical chord. Removed lower dryer panel. Removed two bracket screws and bracket that held coiles in place on top of gas valve. Disconnected electrical clips and removed coils.....note that one coil is inverted as compared to the other. Cannot confuse as the electrical connectors are different. Slid on new coils, replaced bracket, carefully replaced screws. As space adjacent to coils is tight, be careful in tightning screws so as to not strip heads. Connected coil electrical clips. Plugged in dryer electrical cord. Tested dryer by starting up. Success, gas ignition. Cleaned out dust/lint on the inside of the dryer cabinet before closing up.