ADE41FSS171TN01 Speed Queen Dryer - Instructions

I had already taken the dryer apart prior to changing the felt seal. Had oiled the rollers, greased the bearings & vacuumed the whole inside of the dryer out. Had used a high temp lubricant on the seal & had stopped squeaking for about a month. I ordered 2 seals & when they arrived, I popped the top of the dryer off using the putty knife to pry the spring latches. I opened the top up & leaned it against a wall. I disconnected the wiring to the light & the switch in the door, making note of the wiring order. Then used a nut driver to take the 2 screws from the inside out, that holds the front cover in place. Then the same for the 4 screws holding the front bulkhead in place. Then lifted up & out from the unit. Then used the putty knife to scrap the adhesive & old seal off the bulkhead. Cleaned as much of the adhesive off, then applied some high temp silicone adhesive to the bulkhead, placed the new seal on, using some clamps to hold it in place. After making sure it had adhered to the seal & bulkhead. Did the reversal of the above mentioned steps. Moved the unit to laundry room, plugged it in then started it & voila no more squeaking dryer.

Early in the life of my dryer, the Cylinder Seal came out. For the past two years I put off buying the part. When it came in, I p[opped the top of the dryer, removed the two screws holding on the front panel, and pulled the Cylinder of the back wall of the dryer. I then placed the seal in the right spot, glued it down and reassembled. About Fifteen minutes of work and a cheap part, and now my dryer dries a l;oad of clothes in an hour instead of three.

After removing the front panel, the igniter just just snaps into the bracket.

remove bottom two screws on lower front panel, remove panel. remove two screws on lower portion of door panel, pull bottom panel towards yourself to release pins at the top. Disconnect wiring for light and door switch (make sure to note what wires go where. Complete removal of front door panel. Remove 4 screws holding cylinder frame in place, lift to remove. remove remnants of old felt seal, use rotary tool to remove excess glue, etc. apply glue (used rubberized gorilla super glue), apply felt seal - allow glue to set up. reinstall in reverse direction from removal. Be sure to use glue as there are no clips or other retaining pieces for the new felt and it will not hold in place. overall pretty easy.

Super easy. 2 screws allows you to remove the access panel. One screw on the igniter bracket removes the igniter. Pull off the 2 wire connectors and plug into the new one. Test the dryer and close the access panel.

Removed the screws on the dryer vent and the back of the dryer top. Then I raised up the top panel and removed the screws that held the front panel on. I removed the front panel to access the coils. I replaced the coils and then the front and top panel and screws. All went well. The dryer is working properly now.

Unplug power. Remove the lint filter and remove the 2 screws under the lint cover lid. Use flathead screw driver to pop off the top of the dryer housing. The clips are located at the front two corners.Just wedge and lift up to unclip. Remove two hex head screws on each side disconnecting the side housing from the front housing. Disconnect the wiring harness at the front top right side if you are facing dryer. Lift up on the front housing to unclip the bottom of housing. Just lift up and pull housing face toward you at an angle. The circular dryer piece where clothes go into will be loose but still attached. It will sag down a little. Then on bottom left side unscrew two screws to remove the 2 coils. You will need a stubby phillips screw driver about 1.5" long and you will need to lift up on the dryer circular piece out of the way a little. Once you remove the crews, remove the clip holding the two coils. Remove the wiring from the coils. 1 coil has two leads and one has 3. Replace one at a time just in case your model is slightly different. Be sure to install the coil with the little knobby part up and in alignment for when you reinstall the clip/ bracket that holds it in place. Replace the coils and install the racket/ clip with 2 screws. Reinstall the wires. Reinstalling the front face of dryer housing is a little tricky because you have to slide the bottom back onto the clips while holding the circular dryer part up. Then push the front housing up against the circular piece so they are aligned and fit. While holding it, screw the two hex screws on each side. Then reconnect harness and snap the top housing back onto the front face housing clips. Reinstall the two screws at the lint trap. Reinstall the lint trap and plug back in. The dryer is now fixed if that was your problem. Its a fairly simply job once you start doing it. Good luck.

I follow the instructions provided on the your web site, the instructions were very easy to follow and to the point. In all it easier than expected. your information regarding the probability that the indicated part will solve the problem are great! That gave me a good feeling about ordering the part from you. Thanks for your help.

rts came quickly & I got started. First, I unplugged the dryer and pulled it away from the wall about a foot. this was done so the top would have clearance when it was lifted up. Next, I removed the lint trap and then took the two screws under the lint trap door out. Then you use a screwdriver(flat blade) to release the top of the dryer. The release points are about 1-2 inches from the edge of dryer. Next pull the wire connector apart so the front can be removed. The connector is on the right side, front corner, facing the dryer. There are two hexhead screws near the top on both sides. Remove the and the front will come apart as you lift it slightly. Then you disengage the tub belt. Once this is done the tub can be lifted out and set aside/ take care to remember each things position as you take it apart, so you will not get confused when you reassemble. Now the solinoid assembley is easy to get to. Use a phillips screw driver and remove the two screws that retain the bracket that holds the solinoids in place.. Lift the bracket and remove one solinoid at a time. Pull the wire from it and plug the new, like solinoid to the wire and put it back in place. then do the other one. set the bracket back over the new kit and replace the screws to the bracket. Set the tub back in, rethread the belt to the drive wheel. Next put the front back on making sure the bottom part slips into the two sides of the dryer.Replace the hexhead screws on each side; plug the wire connector together. Now , pull the lid down into position and press into place. Replace the lint trap screws and replace the lint trap. Plug dryer up and we are done. Repossition the dryer to its original place. It really was not a hard job at all. Thank-you Susan for your help and expertise.

Dryer was getting hot at start of cycle and would drop out flame and then cycle flame every 45 sec to 1 min. Pulled of panel to observe this and thought it was a heat sensor problem. Went online and people were saying a coil could be bad. I took coils out and tested them and they tested good but I bought new ones anyway as I figured they were going out of range as they heated up, This proved correct as dryer works .

Unplug dryer first! Remove toe panel with 1/4" nut driver on each lower corner. Gas assembly will be on the right immediately below right of drum. Use a short Phillips screwdriver to break loose two screws retaining hold-down plate on gas valve coils. I used an adjustable wrench to turn the screwdriver on screws which are not easy to apply torque to. Each coil will easily slip off stem. Disconnect catch on plug with very small flat tip screwdriver for each coil, then pull off connector. Ensure the 3-terminal coil goes to the front and the 2-terminal to the rear. Note aligning tips on coils which correspond to holes in hold down plate. Reassemble in reverse order except for toe panel. Plug in dryer and verify gas valve operation and flame presence. Replace toe panel.

Diagnose that the circuit is functioning up to the igniter. This is done by removing the peep hole cover on the bottom front panel, turn the dryer on and watch for a glowing igniter. My dryer would still ignite the first time because the coils would not show an "open" until they heated up. So if you see the igniter glow it is most likely your coils are bad. Remove two screws from lint trap area on top of dryer. Pry up on top panel at the two clips. Panel is on hinges, so flip it out of the way or just brace it with something enough to keep it off the front panel. Remove the two bolts from inside top corners of the front panel. Use a small punch or screw driver to push in on the tab to release the doors electrical connector. Pull straight up on front panel to remove it from bottom clips. The gas valve is very easy to get to without removing the drum. If needed for inspection or cleaning, just pull back on the belt tensioner to remove the belt from the motor and then pull the drum out. Or just use a stubby phillips screw driver to remove the bracket from the top of the ignition coils. Use a very small flat head screw driver to lift the locking tab on each electrical connector while removing. Remove the coils and place new ones in very same position (note the tab or key way of the coils faces up and are defined in the bracket). Re-assemble all parts making sure connections are tight and drum is correctly mounted. Note: if you remove the drum, return the belt back, in a loop, through the tensioner. This part hurt my head for a moment because I did not pay attention. Also a good idea to vacuum the debris and lint while your in there! As always check to make sure the exhaust pipe is clear. Have fun!

Followed directions from Youtube video

Open top of dryer, then remove front. Coils on lower left. Unplug and replace coils. Vacuum loose lint from bottom of dryer. Replace front then top of dryer. Test run. All good !

I watched a video. The man speaking was Wayne from parts direct. He made the repair go so smoothly. I enjoyed watching him and I hope you include him in more videos. Had dryer apart and back together (after I had to take top back off, to re-attach the door switch, which I forgot. Had a senior moment!!) in 15 min.And working as good as new. Thank you Wayne. Have a nice day. Bryan