AE9233 Speed Queen Dryer - Instructions

clothes drier didn't work, tore the drier apart, found problem went looking for the part locally, didn't find it, got mad, went on line, found Parts Select, ordered part, part under $20.00 delivered, part delivered, put everything back together , can dry clothes again, didn't have to find $350.00 to go buy a new drier. Merry Christmas!

Lifted the top of the dryer removed two screws and pulled the front of the Dryer forward. Slipped the new belt over the drum and over the motor pulley.
Pushed the front back in place and snapped the top of the dryer down and the job was complete.
I thought the part would take three days to get here.
It was delivered the day after I ordered it.

To start the repair, I removed the two front panels. Disconnecting the wiring to door and light. Next removing dryer drum and drive belt[ allows access to belt tensioner] replace tensioner roller, then reassemble. Dryer works fine

once I found where the heat element was, it took me a few mintues to remove the bad one and replace it with the new one that came before the due date. very good instruction in kit. Be sure and leave the old one hooked up until the new unit comes in so you can do a easy exchange of the wiring.

Determined no air flow or heat through system even though dryer spun and timer worked. Ouside vent dispelled no air. Opened dryer panel.
Blower wheel/fan broken off from shaft. Googled appliance parts ... found ... Partselect .... keyed in mfg, model number ... schematics available ... found part ... ordered ... received in two days ... installed ... reassembled. Working fine ! $ 30.00 compared to buying new dryer ! This was a refreshing and rewarding repair. If it could always be this smooth !!! Great resource ... PARTSELECT !

Removed 2 screws on the bottom of front panel of dryer & pulled it off. Next I got down & looked to the back & bottom inside of the dryer. I spyed the heating element,I pulled off the two wires from the thermostats[ orange & black. I removed two screws from the heating element plate & dropped it down & removed it from the dryer. Reverse procedure to reinstall. Will see if we can get another 10 years service out of it.

removed front of dryer, replaced old pully and put on new belt.

removed old element, relaced with new element , thermostat dryer works better than it has in along time

Leaned machine back and put blocking under machine to elevate. Removed two screws from front of bottom panel. Lift panel out and set aside. Next remove two bottom screws from door frame. Pull bottom of frame out and up to release. Remove wire clips from door light and switch. Set door frame aside. Inside drum, take three phillips head screws out, that hold filter frame in, remove filter frame. Next remove four front screws on drum alignment face plate. Set aside. Grasp drum and pull forward, off back guide rollers. Drum will drop down a little, reach in around drum and slide belt off. Remember to look in under drum to see proper placement of belt aroun motor shaft and idler pulley. Replace new belt around drum with ribs against drum. Route belt around motor shaft pulley, pull idler pulley toward motor and place belt around pulley smooth top runs against pulley. Reinstall everything you removed. Connect wires to door.

Just snapped the new plastic latch into the hole (the hole was there because in trying to extract the old latch, it fell into the inside of the door). Took two seconds. Order to arrival of the part took only 22 hours!

Fairly easy to repair once I figured out how to get it apart. The amazing part of this was searching the web for the part. I found PartSelect, ordered it at about 2pm Eastern time and the part arrived the next day! I will definitely use this service again.

Took apart front of dryer, took out tub, replaced pully wheel, put tub back in with new belt, and put front back on. I would recomend replacing wear pads when doing this type of job.

First I unplugged the dryer and turned off the gas. Pryed up the top of the dryer at the front corners to free the front panel. Removed the two screws at the bottom front of the front panel. Then disconnected the three electrical connections for the door button. Put the front panel to the side. Then took out lint tray and then removed four screws that hold the lint blower piece and put it aside. Then I could see the motor and the idler assembly is on the back of it. If you have a camera take a picture of how the belt is on the pulley. If not you can draw a general idea of the direction. I reached back and slipped the belt off the idler pulley. Removed two screws from the front bottom of motor fork .Removed two screws from a small electrical hook up thats on the front of the motor and removed it. At this point I could just slide the motor out. With a rachet and a regular wrench I removed the small bolt holding the arm on. Put on the new arm. Slid the motor back in and reconnected the belt. Put everything back together in the same way. Yeah it works. I am a 58 year old woman and this job required no brute strength. Don't be intimidated its really not that difficult to fix it yourself.

I just lifed the old grate off and layed the new one in.

First - I did some research on line as to the possible problem with this dryer.
I had already taken the front apart before, so I knew what was needed to remove the door and front.
Remove the 2 screws that hold the dryer door in place with a Phillips screwdriver. Remove the two screws on the opposite side of the door also. Place the door out of the way. The front panel of the dryer now tilts forward. The front panel sits on two clips, tilt forward and lift out of place. The door switch has two prongs that hold it in place, pinch the prongs and the switch slides out. Disconnect the two wires on the switch and connect the wires to the new switch. The new switch slides into place. I tested the new switch before I put it all back together. Took me no longer than 15 minutes.