AE9233 Speed Queen Dryer - Instructions

Installed the new part. Worked great!

I unscrewed the door catch and pried out with some resistance the strike part. Screwed in the catch and pushed in the strike. Closed door. Voila!! Back in business with assurance.

The door switch was easy to replace. It is located in the right bottom of the door and I popped out with my fingers. Follow the wire connectors from the old switch and remounted back in.

Removed the 2 screws from the bottom of the front panel and pulled the cover up and out. Labeled the wires to the light and door switch and disconnected. Lifted the belt tensioner arm and unlooped the belt from it and the motor. Removed the 4 bolts that hold the front drum support on then held the drum up and removed the support. Pulled the drum out slightly and allowed the rear to drop, at this point you can get to the rear rollers without pulling the drum out of the machine. The roller shaft was so tight I had to put a straight-blade bit in a 1/4" socket to get enough torque to break it loose. Make sure to use a large enough driver or you will strip the slot out of the screw. This model had a nut on the back but I was able to just drag my finger against it to get it apart. Removed the washer and roller from the shaft and cleaned the shaft and washer with WD40 before reinstalling with the new roller. Vacuumed all the lint I could get to and reassembled, lift drum, push back, front support, 4 bolts, belt, wires, front panel, 2 screws.

removed a couple of screws and replaced the new fuse . the dryer is heating up ok now.

p.s thank you for the quick deliever on the part, . as i was only with out the dryer for two days

Thanks
JoAnn

My 11 year old daughter broke the door clasp to the dryer by repeatedly slamming it trying to get it to close. I told her to go down stairs write down the make model and serial number and come back up and find a place to buy it online. I left with instructions not to use the computer for anything else until the part was found. Less then 15 minutes later I came back because I heard giggling. She was chatting but had found an exploded view of the door and the part. She was very pleased with herself! We bought it and it arrived a few days later. I saw the empty box. She had opened it and taken it down and installed it herself. A good lesson, for her and me

Well tried to find this simple part around Columbus and even maytag website no luck.Parts select had it to go and arrived earlier than expected.Fixed it less than 5 minutes works great.taken longer to put the light bulb back in,Really like the accuracy and quick response from parts select.If I had called a service tech probably would have cost $50.00 or more for a part that cost a little over $3.00 and saved this site in case I need to order other parts.Thank you

Removed the front panel of the dryer and drum to replace the rollers. You will need a snap ring pliers to remove the locking snap ring holding the rollers, replaced rollers, installed new drum belt and replaced the front dyer panel.
Tested the dryer no more noise.

Thanks

You have to take apart the whole dryer to get to the belt.Nut driver with cordless drill make it go so much faster.Unplug dry, take apart dryer and replace with olr belt with new belt.Takes about 20 minutes to do.plus I took off the two guide wheels on back of cabinet and greased everything.Works like brand new.I had a repair guy tell me I needed a new motor.If you can spin the drum by hand replace belt first.

used one nut driver, basically took the whole machine apart. took snap ring off the idler shaft, replaced pulley, and put it back together. simple job.

removed the lower cover, tipped the dryer on its back for easier access, unscrewed the 2 mounting screws removed the heating element, installed the thermostat and and high tempt relay on new one replaced the wires reinstalled the new element, very simple

Removed the front dryer panels (lower & upper), front drum support and drum. This gave me easy access to the idler pulley and tension spring. I also took the opportunity to vacuum all of the lent that had collected over the years. After installing the new parts and aligning the belt, I reassembled the panels, plug it in and it worked like a champ! Locating the parts on your website was fast and easy. I appreciate it and thank you.

removed drum and motor and installed new parts. Very fast service on parts. Well be back if needed.

Took off the two lower front screws, Then the screws to take off the door and frame. Then the lint trap. Finally took out the drum. BOY WAS MY DRYER DIRTY WITH LINT! Vacumned it all out and washed the filter and filter housing with soap. Found out that I needed tension wheel also. Ordered that. Replaced the wheel, that was the hardest part. Need to take off this part like a "spring washer" and put it back on with the new wheel in place. Then placed the belt on the drum, belt on the tension, screwed the drum holder frame on, screwed the door frame on, screwed the lower panel on and it works great. By the way I am a female and if I can do it anyone can.

remove the housing under the dryer door. take out the lint trap. I took the whole bottom off the dryer to easily get to the tensioner pully. I then loosened the tub and slid off the old belt and replaced it.