DV203AEWXAA Samsung Dryer - Instructions

Remove 2 screws which hold dryer/washer together on back. Remove 2 screws back top dryer and slide top back. Remove 4 screws top dryer that hold timer panel. Remove 6 screws that hold front panel on..4 on top of panel and 2 inside door. Disconnect wires to door at slide connection. Unplug dryer..this is actually 1st step. Remove 1 screw on heating element (lower right). I found that by removing the red wire the element will wiggle loose and come far enough out to disconnect black wire. There are 4 other terminal connections which are jumpers that will slide out with element. Note where wires attach and remove all. Use Multi meter on highest ohms setting or a continuity tester to test heating element - thermostats - thermal fuse. They should all have continuity between terminals. Replace any that don't . My thermal fuse was open (no continuity). I replaced it and had heat..but inadequate heat. Got new thermostat which fixed problem. Video I watched said to replace them together..I guess he was right. I suggest that while you have dryer pulled out to take time to check/clean dryer vent..also flapper outside.(mine had lint built up in hinge and prevented flapper from closing letting cold air and anything else in). Parts Select has great videos/skematics and even with "snail mail" delivery part was there in 2 days. They are the best!!

The repair was pretty easy to install the heat element, but had to replace several other parts do to the manufacturer that had broke off

IMPORTANT!!! Unplug the unit first!! 1 - Remove two screws on the back of the top of the unit. Pull back a little on the top to release it from underneath the control unit on the front of the dryer (the piece with the dial and buttons). 2 - Remove the four screws from the control unit. They are located at the top of the dryer. Pop off the control unit - don't worry about breaking any wires as there are none. 3 - Remove the front of the dryer by removing the four screws that are NOT used for the door and door latch. I had also removed the door latch and door but I don't think it is necessary to remove them. The front will swing out from the bottom where you can unhook it and remove it. 4 - the heating element is located on the front of the unit, bottom right. Either draw a diagram of the wires or take a picture of them with your cell phone. Smart phones are great for this as you can zoom the picture if necessary. Remove the wires (they just push on but it may take some effort to get them off). It's either one or two of the wires that are not part of the wiring harness and they go from one part of the element to another so don't get excited if these wires fall down - you haven't done anything wrong, they are just loose. The one screw in the front holds the element in (the back of the unit just rests in that hole). Remove the screw and pull the unit out. Put the new element in, hook up the wires before positioning the element. Put the screw back in that holds the element and put the rest of the dryer back in the reverse order.

*Disconnect power cord before performing this task...(1) Remove the two screws holding top.(2) Remove four screws holding control module, tilt forward, pull up and unlatch. Place module on top, out of the way (still connected by wires). (3) Open dryer door, remove two screws holding lint trap assembly, close door. (4) Remove four screws on top of front cover, disconnect door light wire, tilt front cover forward, lift up from catch at bottom and remove. (5) Disconnect moisture sensor connection on bottom right for easier access to duct assembly. (6) Remove three screws holding duct assembly support bracket in place, raise duct assembly six inches to allow the bracket to be tilted toward rear and lifted out of the way. (7) Disconnect Red and Blue wires from front of duct assembly and pull assembly carefully from the rear of the unit and out the front paying attention to the wires still connected. (8) Remove wires connected to the thermostat and thermistor. (9) Remove screws holding in both units and replace with new components. (10) Reverse process and test. *note* if the unit appears to heat but clothing still wet, make sure moisture sensor was connected (I must have forgot and got to go back in to check, ooops). Regardless, this is an easy task. Could be intimidating at first but after the part has been accessed twice its no big deal and can be done over a lunch break.