7216A REV B Norge Dryer - Instructions

I took the back of my dryer off to see if the problem was there. I saw that the belt was broken and laying on the inside of the dryer. Took belt and went on line (Google) my KitchenAid Dryer from it's model number. The website was PartSelect. Found the belt I needed and saw a video on how to replace the belt. I called to order the belt and spoke to Steve, which help me with all my needs. Steve knew just the belt I was looking for and placed my order. The belt arrived a few days later. While I was waiting for the belt to come in, I removed the front of the dryer and get ready for reinstall. It took me about 15 minutes to install the belt and put the front of the dryer back together. I found PartSelect to be very helpful and saved me, maybe $150.00 by not having to call a serviceman to do the easy replacement. Thank you Steve and PartSelect, now I'm number 1 with the wife again.

This Was pretty simple, removed the old broken screen. There are two torque screws on the outside where the bottom of the door is, I removed them so I could move the screen on the inside so I could clean out the excess lint. vacuumed out the lint, tightened the screws back in and slid the new screen in and it was done.

First, I unplugged the dryer. I pulled up the lint filter, then unscrewed the two screws there. Then pulled up the top panel. I had a helper hold it up since it couldn't lean against the wall. Then I had to take the front panel off the dryer. The idiots at Kenmore used screws, not pins, so I needed to use a socket wrench to get those two out of the top corners. Then I lifted it up and off. I removed the broken belt. I put in the new one. I replaced the pulley, which had fallen without the tension of the belt holding it in place. It was pretty easy to figure out how it went, but I consulted the online community for a diagram. I threaded the belt in place, replaced the panels, and viola! It worked. Easy.

Step 1. Read all the comments about how to do this job in this forum. (i found them very useful)

Step 2. Read the directions that come with the dryer (they helped a lot)

Step 3. Don't forget to disconnect the power cord before reattaching the door switch wires (oucH! ) or doing anything with your dryer.

Removed the two screws holding in the Filter and removed the filter.

Removed the two screws holding the front onto the dryer.

Put the belt over the drum and proped the drum up.

Reseated the tension spring and pully in the proper slot. (On my machine it is the position closest to the motor).

Reassembled the dryer in the reverse order.

-Took top of by prying with screwdriver.
-2 screws and door wire to take off front panel.
-proped drum with 4X4 piece of wood.
-looped belt around drum where the mark for the old belt was.
-looped belt through tensioner and pulled with the screwdriver over the motors drive shaft.
-manually spun drum to make sure everything was right.
-put panels back on and was done.

You cant go wrong with the included directions and belt diagram. this is the first repair I've done of any kind that went flawless.

Pull dryer out from wall about 6 to 8 inches step 1 - romove front/bottom access panel. Step 2 - remove lint trap and remove 2 screws (philips type) that is under lint trap door. Step 3 - push in 2 wood shime in front edge between lid and front panel (angled shims like door shims - a putty knife will work to, just be carful not to scratch finish) step 4 - fold lid upward and back (like on a hinge) step 5 - looking from where the bottom/front acces panel was losten 2 screws - one left one right about 3 turns - 9you can remove them it just makes it easier to reinstall the front panel. Step 6 - find appropriate pot or stacked 2 x 4 pieces - something to hold up the drum when you remove th front cover, and from underneeth support the drum. Step 7 - look thru bottm front access hole - there are 2 springs that come down from the door - and clip onto the frame of the fryer - unclip them and place on the side. Step 8 - remove 2 upper screws that hold front panel on, and remove front panel, if you left the bottom screws attached but loosened you have to lift up on the front panel a bit. Step 9 - looking from the bottom thru where access panel was - you will see motor on right with a additional roller (tensioner) - push upwards on tensioner to relieve pressure on motor and pop off belt (remember where tensioner is and how it clips in to base. Step 10 - work belt off of drum towars front - to remove it all the way you will have to lift up the drum slightly off of the pot or whatever you used for support so the belt can clear. Stem 11 - new belt goes on the same way you took to old one off - plat side away from drum with ribs against drum. Step 12 - again lift up on drum and work belt back on. Step 13 - tricky part is how to get the belt back on the motor - prentend you are threading a needle wht a folded over piece of thread - hold the belt with about a 4" loop with your left hand - hold up on tensioner and feed it back thru and work belt back over end of motor pulley, after front panel is back on with the 4 screws tightened spin the drum and make sure belt is between the 2 lines marked on the drum and remove the pot or whatever u used to prop up the drum. Dont forget to attach the springs for the door assemble all other components in reverse order. And dont forget to take the pot back out

I replaced it

The dryer was not difficult to repair. The diagram that came with the belt made the repair easy. The repair part came in a very timely manner.

- Unplug the electric dryer.
- Manually opened the top of the dryer.
- Unclipped the wire assembly attached to the front panel of the dryer.
- Removed two screws holding the front panel of the dryer, and remove front panel for access.
- Very Important!! Note how the old dryer is currently installed before proceeding.
- Rotated the dryer drum while working the dryer belt toward the rear of the dryer.
- Removed the dryer drum.
- Removed the old dryer belt.
- Put the new dryer belt around the dryer drum and put the dryer drum back onto the drum rollers and into the rear guides.
- Here's the hard part, lay on floor and reach into the pulley area and motor - wrap new dryer belt around these belt rollers as "noted" in the fifth step.
- Rotate dryer drum by hand to ensure the new dryer belt is exactly installed as the old dryer belt.
- Reinstall front panel.
- Reclip wire assembly onto the front panel.
- Manually close the top of the dryer.
- Plug in the electric dryer.

Removed the two screws at the back that hold the top of the dryer. Then I pried off the top at the front by inserting a screwdriver into the front to remove the top from the clips. Then I tilted up the top like a car hood.

I removed the two screws inside that held the front on and lifted the front off. Because of the wires attached to the front, I made sure to turn the front aside without pulling on the wires. After removing the broken belt, I put the replacement belt over the front of the drum, lifting the drum a little. Then I threaded the belt over the drive and around the tension wheel per a diagram I found on the web.

While I had the front off, I removed the lint trap and cleaned out probably decades worth of lint.

Then I replaced all the parts in reverse order, plugged it in and had a working dryer!

I pried the top of the dryer with a screw driver and then lifted the top of the dryer, I then removed the two screws "with a nutdriver" that held the door in place and then removed the door and drum. I then got the new belt and placed the belt over the drum and positioned the belt through the idler arm and then on the motor pulley. I had to hold the door and drum to lock the bottom of the dryer door to the dryer and then made sure the rear drum seal was in place and the belt did not slip off the motor pulley

Opening the dryer to discover the problem was easy. We put the belt up on a workmate bench - I think this made access better at the bottom. Getting the new belt on past the rear drum seal was ok, the instructions could benefit by including wording describing how to roll the belt flat under the 2 rear drum support pulleys to bring it to the drive motor shaft pulley. The instructions included with the belt had a diagram showing the position of the belt take up idler (the idler was found loose inside the bottom of the dryer), our dryer had a hole in the metal spring clip of the idler arm, so we thought at first that a screw to the chassis had broken - this is not the case the idler pulley is held in place by belt tension, so pulling the spring clip open while feeding the belt would have been useful in the instructions too. Other than those 2 head scratchers the repair was easy and saved us the cost of calling a repairman. Thanks PartSelect.

My 12 year old son and I took off the front of the dryer to see if we could see what was wrong. The belt was snapped and on the floor of the dryer. I ordered the belt from you--it came three days later. That evening, my son held the drum while I laced the belt through the pulley. We cleaned everything up--lots of lint! Put everything back together, plugged it in, turned it on--SUCCESS! We were wildly excited. I am a stay-at-home mom determined to save money any way I can.

First, I printed one of these responses which were excellent and very detailed. The screws connecting the lint slot to the top of the dryer was frozen. Taking the front panel off was difficult because I did not read the instructions I printed out very well. After I took the top off I had a hard time finding the 2 screws located inside on the top of the front panel. They are located to the far right and left at the top. To take off the front panel you have to push it up to release the clips on the bottom, then it comes right off. Taking the drum out was easy. What was difficult was putting the belt on. There wasn't any slack and to put it around the pulley and the drum for me was difficult. After that is was a piece of cake. It works great.