7216A REV B Norge Dryer - Instructions

Checked the voltage to the high limit switch. Found that the element was bad. Ordered the part from partselect.com. and received the part in two days. Unplugged the unit, pulled the lid on the dryer, used the 5/16" nutdriver, removed 3 or 4 screws, pulled out the old and installed the new. Saved a $100.00 service call from the repair man! Novice in home improvement can do this. Thank you Partselect!!!

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

I took out the old worn out part and replaced with the one I order.

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done

Lint filter replacement is routine maintenance. operating without a filter causes problems, a dryer sheet was sucked thru the opening and into the blower wheel, causing a lot of noise, and shaking because of the unbalance. I popped the top of the machine up, removed two screw holding the front in place, removed the front, gaining access to blower.
Removed the offending sheet, straighted the bent fin, and put everything back together again. Installeed the new filter, now it runs smooth, and quiet. mission accomplished.

Once I realized it was just a drum belt and how easy it was to fix, I ordered the belt myself with no help from a national warehouse hardware chain where the manager said "I don't have a belt but I can sell you a dryer." Thank you I kept my 300+ dollars and once I got the belt it only required removing the two screws that sealed the lint screen cannel to the top; popping the top, removing the to nutbolts fastening the front to the side panels; slidding the front panel out; putting the belt around the drum and attaching it properly to the tension pully and motor. Finally, I closed it up and tested it. Household hero in less than 12 minutes! Not bad for a psychologist, eh?

Disconnect power. Removed front panel and lifted top. Removed belt around spring pully and motor assembly. Carefully eased belt around back of drum and gasket. Reverse process.

first I took the two screws that hold the filter in, then disconected the power,then I poped the top of dryer up and removed the two 5/16 screws on the inside of the front panel then the two screws down by the loading door hinges and took off the front cover and the drum, replaced the belt and put the ajuster back on and put everything back in revers order and it is working like new thank you for the fast order .tony

Watched the video on the site and it was spot-on! Super-easy, took like 10 minutes to replace the belt. Thanks!

Took two screws out of the Lint tray on top. remove to bolts from under hood then put new belt on. Always make sure there are no twists in belt when put back on

I unscrewed the door catch and pried out with some resistance the strike part. Screwed in the catch and pushed in the strike. Closed door. Voila!! Back in business with assurance.

Just slid the new filter in.

Watched a video and went to town taking it apart. I stuck a pop can under the barrel to hold it up while I worked on pulleys. My dryer does not have a plastic pulley but a metal tension bar with a hole in the middle. Ran upstairs and watched a different video with my set up and all was good. 5 min of work 5 min watching Youtube and 5 min cleaning all the lint out of the machine. I am actually glad the old belt broke because some of the lint was in a clump and had scorch marks on it. I took the shop vac to every part of the cabinet and shoved it down the lint trap sleeve also.

Screwed the new “$40” dollar light bulb back into the recessed socket. The new bulb is much smaller that the original bulb and much harder to get fingers into small area where the bulb went. After several try’s, I got it in.

DISCONNECT THE POWER. Double check the dryer is unplugged. Use a putty knife to free the latches holding the top of the dryer in place. Lift up the top of the dryer and secure it in place (be sure it's safely held open and won't come crashing down onto yourself as you work). Remove the two screws on the inside and near the top of the dryer, which hold the front and side panels. Gently lift up on the front panel (it may help to open the dryer door to get a better grip). Once free from the bottom clips, carefully rotate the front panel so that the door sensor wires are not strained. Once the front panel is out of the way, grab the drum and firmly lift it up and away from the back. (The drum has rollers and ridges at the rear and you'll need to pull the drum out of its "track"). Slide the new belt around the drum and position the drum about halfway inside the dryer. Loop the belt around the motor, but not the tensioner, (it will be easier to install the drum if you wait to tension the belt). With the belt around the motor, gently slide the drum back keeping the belt around the motor pulley. Press and guide the drum back onto the rollers at the rear. Check the belt is positioned correctly around the drum and motor. Reach back from the front and loop the belt around the tensioner. Rotate the drum by hand and make sure the belt is aligned and the drum spins smoothly. Position the front panel and slide it onto the lower clips. Install the screws being very careful not to drop them into the abyss... Close the lid and plug in the power.