MDE3050AGW Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jim from Germantown, WI
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
old latch broke
I inserted the clip
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Virginia Beach, VA
- Parts Used:
- WP6-3705180, WP6-3700340, WPY312527, WPY014874, WP33002535, WP315772, WP354987
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer made loud screeching noise.
After reading all the other repair stories on Partselect, by the way thank you all, I removed the door, then removed the two security hooks that hold the top secure. Then I removed the front panel. I then marked all the screws on the outer door and shroud so I could easily put it back together. I left the all the wires connected and set the shroud and outer door to the side and removed the drum belt and drum. Removed the spring off the idler arm, then using nutdriver, removed the screw that secures the idler arm to the motor. Assembled the new idler arm parts and reversed the process to put it all back together. If I would have replaced the idler arm assembly the same time I replaced the drum support rollers, I wouldn't have had to do this twice! But now I am an expert repair tech on this particular model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Swanton, OH
- Parts Used:
- WP303396
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Dryer ran hot
Took off door, then removed front of dryer to access the internal controls. Project went pretty darn well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Hamilton, MT
- Parts Used:
- WP33001621, WP22001664, WP22001659
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
knob retainer hole was broken
Ordered the part..... waited a few days fro it to arrive, (it came quite quick considering). Sat down in my easy chair and assembled the knob and gave it to my wife to slip it on the dryer. Whew, I was beat.... hehe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- matthew from Central Islip, NY
- Parts Used:
- WP33001762
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
no heat, coil wasnt getting hot
took old one out then i had to strip the connector off new one was to big...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leo from HOUSTON, TX
- Parts Used:
- WP6-3700340, WP33002535, WP33001808, WP33001807, WP33001767, 306508, 12001541
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
metal banging noise as dryer drum rolls
Used PartSelect videos to first diagnose the problem which was worn drum felt seal. Then, used the same videos to replace parts, both needed and convenient to replace b/c of already have access.
While the videos were very helpful, first timers should be aware that there are significant knowledge gaps between a professional's easy repair vs an amateur attempting the same.
While the videos were very helpful, first timers should be aware that there are significant knowledge gaps between a professional's easy repair vs an amateur attempting the same.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from PROCTORVILLE, OH
- Parts Used:
- WPY312527, WPY014874, WP6-3705180, WP354987, WP33002535, WP315772, 33002459
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Squeeky dryer
Okay, first of all, just let me say, if I can do this, ANYONE can. I am not very handy when it comes to things like this. I watched online videos and they will walk you through everything. I am so pleased with the results. Quiet as can be now. Before, we would have to shut the door when it was on because the scretching was so loud! The parts on this site were far more affordable than at my local repair store and they all came right to my doorstep. Overall it took me about 45 minutes and three beers :) Good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from Missouri City, TX
- Parts Used:
- WP33001621
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Our timer dial had been broken for some time, cracked around the connection to the control panel. I had been able to epoxy glue it to where it was functional, but that eventually failed. We were using a pair of pliers to set the timer on the dryer.
I was able to easily find the replacement part on PartSelect, and the schematics showed me how to easily disassemble my dial (which has three parts) so that only the broken part needed to be replaced. I used a tiny straight-slot screwdriver to pop the pieces apart. Once we received the new piece, it was very simple to pop the pieces back together and have a fully functioning new dial!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RODNEY from Spokane, WA
- Parts Used:
- WP6-3129480, 33001801
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Terrible sqeel as dryer rotated.
A year or so ago I replaced one drum wheel. The dryer worked fine for months until it started sqeaking again. When I removed the wheels again the shaft was no longer round but half moon shaped. this allowed the drum to drop lower than it's supposed to. consequently the drum ate through the back drum support. I replaced the back drum support and the roller shafts, in addition to two new rollers. It works great now. The more difficult part of the repair was replacing the rear drum support. It is screwed in from the back and requires two people. Everything else I did by myself. The lesson: If you replace the rollers, be sure the roller shafts are not worn. An asymetric shaft eventually causes more parts to wear out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- claude from laguna niguel, CA
- Parts Used:
- 306436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing, probably broken female latch part
Press in the new female latch part with thumbs. Took about two seconds!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Menomonee Falls, WI
- Parts Used:
- WP33001808, 33001799
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
rodent entry through vent,chewed parts,(distroyed).
Removed the door and machine front.replaced old duct assembly with new ,and reassembled front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- karl from monroe, GA
- Parts Used:
- 306436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer would not stay closed.
I used a flat screw driver to pop out the old female portion and snapped in the new one. Dryer stays shut. That's it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hazel from CONNERSVILLE, IN
- Parts Used:
- 12001541
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
noisy
I watched the video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eli from North Stonongton, CT
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door would not stay shut
Took off the four screws to get to the female clip and used pliers to squeeze it out. Next was using pliers to pinch out the male connector and place the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronnie from SENATOBIA, MS
- Parts Used:
- WP33002032
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Replacing broken Baffles in drum.
Removed four philips screws, two holding door on and two on opposite side of door in order to remove front cover. Then removed two 5/16 screws holding clips that lock the top cover down. Then the top cover hinges up with open access to the drum. The baffles are held into place with two #10 x 1 1/4" screws with 5/16" head each. These had pulled through the drum. Installed new baffles (do NOT come with screws / you'll have to buy some). Had to put small washers (also had to buy) on the screws to hold it onto the drum since the other screw heads pulled through the drum. Closed lid, installed retaining clips, installed door onto frame, installed front cover around door, then screwed door hinges into front cover and screws to other side. Took about as long to write these directions as it did to actually do the work... EASY job!!
Was this instruction helpful to you?
Thank you for voting!