MDE10DAAEL Maytag Dryer - Instructions

I had replaced belt, but the noise continued. Ordered new rollers and washer. Removed the front panel by tipping the dryer back against the wall and removing two screws at the bottom of the panel. Tipping the dryer makes it easy to remove the front panel. Removed the front drum support by removing four (4) screws. I was then able to just move the drum enough to have access to the rollers. Didn't even have to remove the belt. Replaced the rollers. Needed special pliers to remove and replace the retaining rings. Put the drum back into position and mounted the front drum support. Tightened four screws and then put the front panel back on. Plugged it in and tested it. Problem solved. Took about 35 minutes. Thanks

My part was not amazing. What was genuinely cool: I ordered it one day and it was here the next, took out the old and put in the new. Thanks for getting it here so quickly.

Per instructions I printed off online: took off door, then the front panel. Pulled out the old switch/button, connected the new switch/button, made sure the new button was working; put the panel back on then the door and DONE!

Replaced both rollers,shafts, bearings and snap rings.

I removed the cover from the control panel, took out the schematic, removed the rear cover by the motor, followed the schematic, powered the heater by taking the blue hot leg wire off the right side of the switch and touching it to the black lead for the heater on the left side, and I could hear the heater power on. Since bypassing the motor start switch powered the heater, I ordered the part. When it came, I installed it in about 5 minutes and the dryer worked perfectly.

Fallowed instructions on YouTube

Opened your replacement part and found a broken fin on the blower wheel. no way I was going to return it and wait another week for another part. Perhaps you folks need to inspect what you send out. 1 blower wheel with a broken fin and 2 clamps. Replacement was easy and quickly accomplished. Having replaced drum rollers and the belt this dryer is almost new. Thanks

I UNPLUGGED TH UNIT.Removed the 2 screws holding the front panel in place, disconnected the electrical leads on the panel. These screws are located on each side of the panel 3 in. from the bottom. Removed the 4 screws holding the shroud. Disconnected the ground wire on the shroud & set both aside. Installed the new belt per the diagram & instructions. Turned the tumbler by hand a few times to verify proper installation. Re-installed the shroud & front panel including reconnecting the leads & ground wire. You need to use both hands in a tight space to install the belt on the pulley & guide(a littledificult) The new belt fit perfectly & the instructions were easy to follow & accurate.

Followed instruction video

Removed front cover.removed 4 screws holding drum in place. Cleaned out lint from everywhere. Placed new belt over drum looping it over idler arm & motor pulley. Pushed drum back ; rotated drum to see that belt was engaged. Put front drum bracket in place. Put front panel in place with 2 screws at the bottom. Tested motor & rotation of drum; then checked heat. All worked fine. Took 1 hr. but most time spent cleaning lint.

After viewing repair video I used those instructions, after removing drum place new belt on drum, I used scotch tape to hold belt in place, tape belt with 2 inch strip about every foot around drum, leave extra belt that connects to drive motor folded down and taped to drum. After installing drum connect belt to drive motor and roll drum to remove tape. This will keep belt from sliding out of place on drum while installing.

By watching a video I disassembled the front and took the dryer tub out and replace the two rollers and it took about 60 minute.

Removed front panel and tumbler, replaced roller axle,
wheel, and front glides. Anybody can do this.

I removed the front of the dryer and the drum support plate. I drilled out the old rivets and installed the Glides with the enclose rivets. The Glides came loose in a few days! The holes in the glides are larger than in the old Glides. I disassembled the dryer again and reassembled with my rivets. This time I held the rivet gun inside the perimeter of the dryer so that the head of the rivet is opposite the initial installation. So far, so good, except the dryer still squeaks. The idler pulley is now the culprit. White grease burned up. I reassembled with high temperature grease. If that does not work, I will need another idler pulley. The journal looks very worn. the dryer is 30+ years old.

Removed back panel of machine which exposed badly worn idler pulley. Have had problem before on another dryer so I was sure what problem was before I started. Removed snap washer and cloth washer and then bad pulley.(It was very worn and wobbly).Cleaned shaft with small piece of emery paper and put two drops of oil on shaft and replaced old pulley with new one.Put back washer and snap washer.Drive belt had slipped away from its proper position so I had to remove the front panel of the dryer to place the belt back and realign it on the drum and around the new pulley and the motor drive shaft. Not really that difficult.....Machine now runs like it's brand new.....