MDE6800AZW Maytag Dryer - Instructions

Take old out, slide new one in. Perfect fit.

Removed four screws from the door hinges and front panel. Removed the front panel by pulling forward from the top and found two screws. The part does not come with screws which are #10 x 1 and 1/4" long hex head sheet metal screws. I believe that the screw size is critical as the part may break loose again if the screws width is too large or small for the predrilled holes in the baffle. One set of holes in the drum had slotted screw holes which would allow for installing the baffle with the screws partially installed in the baffle. I would recommend washers for that installation. Check all three baffles to ensure that all screws are tight.

I looked on line and found a scematic from your web site to determine how to dismantel the dryer. Once I was inside I was able to determine that the drum roller was making the noise. I decided to replace the other moving part while I was inside just in case. . . Pretty easy job

Unplugged dryer. Removed dryer door with philips screwdriver. Removed front dryer panel aftr loosening philips screws on each side of door. Then at top right corners I used a nutdriver to remove clips/hooks that hold down top of dryer. I then lifted top of dryer up- it is hinged at back. I could then manually turn drum to access screws that hold baffles. I held each baffle in place with left hand and turned in screws with right hand until tight, using nut driver. I vacuumed out inside of dryer. Reassembled top, front panels and door. plugged in and tested. All good.

Removed front panel and tumbler, replaced roller axle,
wheel, and front glides. Anybody can do this.

By watching a video I disassembled the front and took the dryer tub out and replace the two rollers and it took about 60 minute.

Replaced the motor with a new one from partselect per the YouTube video. Had a problem with delivery of the motor. I paid for next day delivery. FedEx picked it up and it made it to the first stop, Indianapolis ok and then stopped. After a week went by I ordered a second one. That one came as promised + 1 day so I’m satisfied. The telephone people were very well spoken and attentive to my discomfort and again I’m satisfied. The motor was at least 25% cheaper than if I bought it from Maytag so the savings is significant, about $50.

The numbers on the metal plates were the JC Penney numbers - that no one recognizes. I eventually found the model number inside the timer case on a printed schematic. I started by disassembling whatever metal covers were removable by finding sheet metal screws and unscrewing them. If you pull on the sheet metal covers, you can find where they are connected to the frame. Eventually, I found that both the heating element was broken and the thermostat was fried. It took a while looking at various websites to find the proper parts. It's all OK now.

Others have described how to remove 4 screws and remove the front panel of the dryer. The problem I saw is that some screws broke off and fell inside while others remained on the separated baffle. The old screws that I found were 1 1/4 inch. The parts manual indicates a replacement screw that is 1 inch long and a number 10 width. One set of holes for the baffles has slotted holes. It appears that wear in the paint indicates movement before breaking off. My solution to the slotted holes was to use washers on the screws and to tighten the screws in the position where any force was not going to move the screws to the center position of the slots. The force of the separation caused the slotted holes to expand.

First removed front door 2 screws holding it to frame, then removed 2 screws holding front cover panel on tilt out front panel, used vac to clean inside, removed idler arm with pully attached, replaced with new parts when I did a test run still had a llitle squeek, the drum support wheel on right looking from front making some squeeking,I went back in removed part shaft had small rust spot cleaned with jewelers cloth lubed and wiped off, no more squeek I wish I had ordered new drum wheel when I ordered idler parts, then I could have done a complete overhaul now I know more I have never worked on a dryer before the drawings on the web site heleped a lot

We could not find directions for the brand that we have. First we took the back off, which we did not need to do.
lift the top of the dryer, remove the front remove drum. Place belt on front of motor, wrap double belt around support on bottom of dryer, open the remaining belt and stretch around drum. Hold drum in place, replace front and top.
Need at least 2 people, not at all intuitive.

First let me say I went on your forum and got instructions where to download a service manual which helped greatly. Unplugged from outlet. Removed 4 screws holding on the front panel then 4 more holding on the front tumbler support and air duct. Removed wires from light and dryness sensor and clips holding wires to panels. Pulled out the tumbler and removed belt. Removed the two drum support rollers and shafts by removing a nut on the back side of each shaft. Removed snap ring off each old shaft, installed new rollers and fiber washers onto new shafts installed snap ring and replaced on brackets with the old nut. Removed tension spring off idler pulley bracket and one screw holding on the bracket. Installed new pulley and fiber washers on new bracket and reinstalled bracket and spring. Placed new belt on tumber and reinstalled tumbler. Used drill and bit to drill out pop rivits holding on the two front glides that are attached on the front tumbler support and installed new glides and pop rivited in. Reinstalled
front support and air duct checking that felt tumbler seal front and rear were in place. Placed new belt on motor pulley and idler pulley. Reinstalled front panel. Removed bulb cover held on by one screw, Installed new light bulb. Also took shop vac and cleaned inside of cabinet when I had the tumber out. Plugged back in and started, sounds and works like new. Ordered parts on Sunday received Tuesday evening Fed Ex. First time dryer repair. Very happy with PartSelect web site and service.

took out the old lint filter and put in the new one.

It fit perfectly! the part arrived quickly.

I was very satified with my experience!

I had to call and reorder because I ordered the wrong part and the gal on the phone cancelled the first order and the right part came the next day!Amazing service!!!

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done