DE710 Maytag Dryer - Instructions

Took off back cover, thermostat was easily identified because of photos I've seen on website. Took 2 connectors off, removed 2 screws and removed old thermostat. That was pretty much it!

NOTE: Replacement thermostat 694674 has an adjustable temperature range setting that MUST be manually set prior to installing! You need to use the enclosed chart to find your original part# and make sure the setting is matched. My original part# 341146 had a "D" setting so I had to change but very easy to do.

After unplugging the dryer, first I removed the two screws that hold the lower front of the dryer in place. Pulling the bottom out slowly releases the upper clips from the dryer top. I then removed the two wires for the door switch in order to move it out of the way. I then remover the four screws that hold the duct and grid to the front of the drum opening from the inside of the drum. I then simply put the new duct and grid assembly in place and replaced the four screws that hold it to the drum opening, replaced the wires to the door switch and replaced the front of the dryer.

First let me say that this dryer is at least 30 years old. The only repairs it has needed up to this point were a set of belts and lint screen holder.

I researched and found a list of items to check for dryer not heating. Only 3 items were listed as possible causes, the Heating Element, Cycling Thermostat, and Heating Element Terminal & Insulator.

First and most important step - UNPLUG THE DRYER FROM THE WALL

To access the cycling thermostat, I removed the back panel. The thermostat is located on top of the blower housing and is easily accessable. I was unable to test the old part.

Accessing the heating element and terminal insulators is a bit more difficult as they are located in the fron of the dryer around the door opening. Further research showed the way to access these parts was to remove the cabinet from the chassis. After photographing the wiring connections, I disconnected the cycling thermostat and motor connections. Next, I removed the 3 screws at the bottom of each side panel. With the dryer door removed (it lifts off when open), I simply lifted the cabinet up over the drum. I recommend having someone assist with this as it is awkward and a little heavy. Lay the cabinet on its front on a rug to keep from scratching the finish. The heating element and insulators can be inspected at this time.

Having found no breaks in the element or insulators, I assumed the problem was the cycling thermostat and ordered one. When I got it (less than 2 days), I installed it and reassembled the cabinet to the chassis. I plugged the dryer in and set the timer. Still no heat!

After looking at the schematic, I found 2 other possible causes for no heat. The motor contains a centrifugual switch (closes when the motor spins) which I was not able to check. There is also a HIGH LIMIT thermostat on the shroud that holds the heating element. I decided I could test this part by by-passing it. I unplugged the dryer and removed the back once again. I reached past the drum from the back (not easy to do) and disconnected the 2 wires from the thermostat and connected them together. I plugged the dryer back in and started the dryer. It heated up like it should. I then ordered the high limit thermostat. After removing the cabinet once again (easier 2nd time), I installed the high limit thermostat and reassembled the unit.

The Dryer is working fine and hopefully should last another 25-30 years.

Followed the instructions on the video, and saved 500 hundred dollars. I was already shopping for a new dryer. Thanks so much!

First I unplugged the machine. I removed the two screws in the front panel and tilted the bottom of the panel out unclipping it at the top. I removed the lint duct whichis held in place with several 1/4" hex head screws. Then I removed the blower cover, also held on wth 1/4" hex head screws, exposing the blower wheel. Using snap ring pliers I removed the snap ring at the end of the motor shaft. Using needle nose liers I removed the spring clamp around the center hub of the old blower wheel and pull the blower wheel off the motor shaft. After cleaning as much lint out as I could I put the new blower wheel on the motor, secured with spring clamp and snap ring. Then I put the blower cover and lint duct back on and put front panel back on.

Replacing the blower fan took way too long, like 4 hrs, because I didn't know how to disassemble the dryer and get to the problem. Replacing the idler bracket and assorted retaining rings and washers was fast, something like 1 hour. Disconnect the power cord, exhaust hose, and gas line. Remove two screws at the bottom of the face of the machine, unplug the electrical harness to the door light, switch and ground and remove the front of the machine. Remove the access panel at the back of the machine and remove the belt from the idler pulley. Remove the four screws holding the front drum support assembly and remove the drum. Replace some old retaining rings and the spring washers on the drum support rollers. Around back assemble the idler pulley assembly with some new washers and the old roller which seemed in good condition. Put it all back together. About one hour.

Unplugged the dryer!!!! Removed two screws from lower front panel. Pulled bottom of front panel forward which allowed clips holding top of panel to release. Unlcipped wires attached to door switch on front panel. Set aside front panel. Removed 4 screws(2 on left & 2 on right) from the drum retainer ring. Set aside retainer ring. Removed thin metal cover protecting blower wires. Removed several screws holding blower cover. Note blower is located on lower left below the lint screen. Used snap ring pliers to remove snap ring securing old blower wheel(an external snap ring). Removed old blower wheel from motor shaft. Inserted new blower wheel on motor shaft. Replaced snap ring. Replaced blower cover. Replaced thin metal wiring cover. Replaced drum retainer ring. Reconnected door switch wiring. Replaced front panel. Done. A hint on the maytag dryer. If your drum wiggles out too far the belt on the drum might not stay aligned. There is a groove on the drum...the belt should NOT sit in this groove...it should ride on the drum about an inch in front of the groove!!!

Using the instructions accompanying the belt I bought from you,I removed the casing an front support for the drum. I then tried to follow the instructions to install the new belt from the front and found it to be absolutely impossible.I saw that there is a removeable plate on the lower right corner of the back that,if removed, would expose the motor and idler pulleys that are the object of the installation so I removed it and,without much difficulty, installed the belt. One problem in doing so involved the belt's tendency to slide into the groove in the drum when manipulating it onto the pulley set so I enlisted the aid of my wife to hold it in place from the front while I successfully and rather easily did so.

popped out old female clasp on dryer itself with screwdriver, undid 2 screws on dryer door and door handle with phillips screwdriver, popped in new male clasp part, put door knob back on and put the two screws back in door and it was all set to go. Less than 15 minutes to do. Better than new and wife is happy. No more duct tape holding door closed now.

I found a broken heating element ( No conductivity with ohm meter) It was fairly easy to thread a new one through. But I tightened the ceramic terminal just a little too much and it cracked. So be careful at that point.

Took off face of dryer (two lower screws below door in front) and then removed the drum which gave me access to the idler arm and idler pully. Vaccumed the interior to remove dust and lint. Replaced idler arm and idler pulley assembly. Replace old belt as drum was reinstalled. Opened rear access panel to complete final routing of the new belt over idler pulley and drive motor. Turned the machine on to check repairs and function. Closed rear access door. Pushed dryer back into place and re-leveled machine.

Sans manual, I turned to the web to find out how to open up the dryer. Maytag uses two Phillips screws on the bottom front panel. Once removed, the front pulls out at the bottom and slides free from the top. Caution, wires on the left side of the front panel prevent total detachment from the dryer. A 1/4 hex screwdriver was used to remove the cover to the blower housing. Once the cover is unbolted attached wires prevent its complete removal and can be set clear of the blower housing. Pliers were used to remove a pinch clamp from the squirrel cage fan (blower assembly) and snap ring pliers were needed to remove the retaining snap ring. The fan was easily removed from the motor's rotor. The loose fan caused damage to the blower housing which I believe was the source of the original rattle. Once the fan had been removed, the housing was removed by using a 5/16 socket on the end of an extension. The replace parts were installed in reverse order and fit perfectly. Other work included the replacement of the drive belt for the drum. PartSelect was chosen because it had the parts in stock and could be shipped overnight.

Switch can be removed from outside of dryer and your video described the repair as having to work from inside dryer. But since wires were still attached to old switch, it could be popped out and wires switched. Since there were three wires on new switch to allow it to turn on and off a circuit, it was useful to check the resistance of the switch compressed or released to be certain I was attaching the two wires to the right two poles of the new switch. But that all required only a couple of minutes. Thank you.

It was very easy to access the parts that needed to be replaced (blower wheel, belt, and glides).
1. Unplug the dryer power cord.
2. Removed the two screws at the bottom of the front dryer panel. Pull the bottom of the panel forward, which frees the retaining clips at the top of the panel.
3. Disconnect the two wires from the back of the panel, and remove the panel. The drum will be resting on the motor/blower hosuing.
4. Slide the belt off of the back of the tumbler, and remove the tumbler (have to angle it a bit, to clear the frame) and the belt.
5. Remove the thermostat cover (piece of angled sheet metal, in front of the blower unit).
6. Remove the screws from the blower housing, and lay it forward, to expose the blower wheel.
7. Remove the snap ring, and then the retaining ring from the blower wheel. Remove the old wheel.
8. Install the new wheel, then the retaining ring, and then the snap ring. Reattach the cover to the blower assembly.
9. Reattach the thermostat cover.
10. On the tumbler, drill out the rivets for each of the glides, and remove all glide parts. Install new glides.

This is a good time to complete any general cleaning inside the dryer cabinet, especially in the area of the motor. Since there is limited access to the motor itself, might help to use the blower function of a shopvac to blow out that dust.
Vacuum out all lint from around the felt drum seals.

11. Loop the new belt over the tumbler, and install the tumbler (the glides go towards the front of the dryer). Note: to keep the belt from falling off, I taped it to the drum with two pieces of painters tape..the blue tape that comes back off easily.
12. On the back of the dryer, remove the access panel, and complete installation of the belt to the idler pulley.
13. If you taped the belt to the drum....don't forget to remove the tape now. Reinstall front panel to dryer.

This was my first experience working with snap ring retaining rings. Even with snap ring pliers, they are difficult to remove without stretching them out. Be sure to order a new one with your blower wheel.

Also my first experience using a pop rivet gun ( to install the new glides). Found a rivet gun at Lowes for $9.99. Worked okay, and all rivets set properly. Good thing, because you don't get any extras with the glide kits.

After replacing the parts, and starting up the dryer, all of the clunking/squelling/rumbling noises were gone. There was a noticable smell while the new glides got broken in...smelled a bit like melting rubber. However, after a couple of drying cyles, the odor was gone.

Removed top screws and the front cover.
Removed lint filter harness/air vent assembly (two screws inside dryer tumbler, 6-7 screws along vent assembly).
Removed front dryer tumbler sealer panel (2 screws on each side).
Scraped off old felt sealer with screwdriver.
Drilled out remnants of old rivets.
Replaced gliders with cork underneath.
Riveted gliders into position.
Used mighty putty to fill the cut metal around the top of the sealer panel (resulting from the dryer tumbler rubbing without proper gliders).
Glued new felt sealer around tumbler sealer panel.
Reassembled the entire unit in reverse order.