Models > MEDB850YG2 > Instructions

MEDB850YG2 Maytag Dryer - Instructions

Jump to:

All Instructions for the MEDB850YG2
106 - 120 of 314
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Ronald from NOVI, MI
Parts Used:
WPW10547292
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
Quick Boil burner would not stay heated and did not reach the required temperature.
The repair was easy. Shut off all power to the range, or unplug it. Remove the sheet metal back from the control panel using a nut driver or socket set. Pull the knob from the front of the control panel. Remove the two Phillips head screws that were hidden behind the knob. Pull the control switch out the back side of the control panel. Compare the old switch with the new one, to make absolutely sure you have the correct switch. Remove one wire at a time from the old switch and immediately install it in the exact same position on the new switch. When you have successfully transferred all of the wires from the old switch to the new switch, reinstall the new switch using the two Phillips screws. Reinstall the knob and the sheet metal cover. Plug the range back in, and/or turn the power back on. Trying boiling a pan of water to confirm that the repair resolved the issue.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Allen from KENNETT, MO
Parts Used:
WP8577274
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Shutting off and had to wait before could turn back on
Followed online video very easy and dryer works like new one....
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from GREENVILLE, NC
Parts Used:
WP8544771
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Dryer not heating
Confirmed I had incoming 240V, checked continuity on element switch confirmed bad. Ordered replacement part. U have to remove drum to replace element
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joe from COWARD, SC
Parts Used:
WP8544771
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set
Heater element had burnt open and would not heat.
I found a simple video on YouTube. I removed the front panel and door. I removed drum and belt drive. Heater element was then easily accessible. I removed all wires after taking pictures of wiring. Element was secured by one screw and one clip and was easily removed. Removed element from element cover. Checked thermostat and thermal overload. Put new element inside of element cover. Then replaced everything in reverse order. Removing lint from inside of dryer was probably the most difficult part of repair. Had to have assistance from my son to put drum belt back on but rest of replacement was simple.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from WELLS, MN
Parts Used:
WP8544771
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set
Electric Heating Element went out.
I checked continuity of all electrical points. I took the top off, then the back, and front of the dryer off so it was easy to inspect the whole dryer. I was also able to clean unwanted dust, and lent with a shop vacuum by doing this.
Keep track of different screws, and mark each screw location with a permanent magic marker. Taking pictures with camera phone is very helpful. Pay attention to electrical connections as well, some of those will need to be dismantled.
Try not to take apart anything more than needed. Watching some online video's can be very helpful as well.
If uncomfortable doing this, call a service repair technician.
I'm a farm boy, and repairs usually come easy to me, but not always.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jack from DINUBA, CA
Parts Used:
4392067
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
Repair video made it easy
Just follow the repair video, it was easy!
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steven from CAMARILLO, CA
Parts Used:
4392067
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
Dryer was making noise - thought it was the belt, turned out to be the tensioner.
I followed the video provided by ‘Partselect’; although it was not the exact model it was close enough to get the job done with high confidence.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carl from MARION, KY
Parts Used:
WPW10359272
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Socket set
Rollers making a noise.
Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Terry from ETTERS, PA
Parts Used:
WP8544737
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
The fan wheel had a blade break off, my bad.
I went on the site and found the part I needed and then watched the video explaining how to dismantle, replace the part, and put the dryer back together. It was easy, especially with the video instructions.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cindy from BENZONIA, MI
Parts Used:
W10120998
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Screen ripped
Dropped new filter in.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donna from CARY, NC
Parts Used:
W10120998
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
The lint filter needed replacement due to what is probably normal wear and tear.
I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rory from LEESBURG, VA
Parts Used:
WP8577274
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Dryer kept throwing the E1 error indicating the thermistor needed replacement
Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back in, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Earl from FRISCO, TX
Parts Used:
WPW10111905
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Door catch was broken
Took a screwdriver and bent wings out a little and then was able to get hold of it with a pair of pliers. Then just put the new unit in the opening and tapped it in. If I had a good pair of needle pliers, it would not have been necessary for the screwdriver.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
ROBERT from GAINESVILLE, FL
Parts Used:
WPW10111905
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Door catch broken
Push in new catch...close door.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Forrest from PARIS, TN
Parts Used:
WPW10111905
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Door Catch broken
Took Putty Trowel and pried out top and bottom then pulled out with needle nose pliers, new part just pops back in (be sure flanges are on top and bottom not sides).
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the MEDB850YG2
106 - 120 of 314