MDG9357AWQ Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Pete from ANAHEIM, CA
- Parts Used:
- W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door switch was defected
The door switch was easy to replace. It is located in the right bottom of the door and I popped out with my fingers. Follow the wire connectors from the old switch and remounted back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JEAN from KINSTON, NC
- Parts Used:
- W10169313
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The dryer door would not cut the machine off when it was opened.
Installed the new part. Worked great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Wimberley, TX
- Parts Used:
- W10169313
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door switch malfunction. Did not stop when door open.
Remove the front,2 screws. Replace switch. Only problem was holding front in position and starting screws at same time. Two person to finish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from NEW ROCHELLE, NY
- Parts Used:
- W10169313
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Door switch broke
Just follow the video. The hardest part is getting the top to disengage from the clips.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from REardan, WA
- Parts Used:
- 306436
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
door bent and when closed broke catch
remove front of dryer with door to get to the back of lach pin. replace front. seprate innor and out door pieces use pliers to remove catch spring clamp ot replace catch screw innor and outor doors back togfther and put tools away your done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Greenbush, MI
- Parts Used:
- 306436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Dryer door catch was broken
Was extrememly simple. Just unscrewed the two screws at the bottom front of the dryer and pulled the front of the drayer out. PUshed the broken catch out and snapped the new catch in place. Reattached the dryer front with the two screws and was done. Less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brenda from gonzales, TX
- Parts Used:
- 306436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
pop it pop it in
used needle nosed pliers, squeezed the latch pop up push new one in. very simple anyone can do it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from Jacksonville, TX
- Parts Used:
- 306436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
door catch on dryer broke
I only had to replace the inside one
I pulled the old one out .
And snapped the other one in
I pulled the old one out .
And snapped the other one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Amarillo, TX
- Parts Used:
- W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken prong
I began by removing the two screws at the lower part of the front panel. After removing the panel I was able to access and remove the broken switch which was located on the front panel. I popped out the old switch and replaced it with the new one, reattached the wires and put the front panel on and the jod was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maryanne from Bethesda, MD
- Parts Used:
- 306436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door latch broken
one screwdriver, one new door latch, five minutes! Pried out the female part of the door latch, tapped in the new one and started the dryer. Never had an easier repair. Usually there is some hitch along the way you learn about the hard way, but not this time. TOO EASY!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Cinnaminson, NJ
- Parts Used:
- 306436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would no longer stay closed enough for dryer to run
popped out the old, broken female latch, popped in the new one in less than 30 seconds. We had been leaning stool against the dryer door for 5 years. Now it works exactly like it is supposed to.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gay from Lutz, FL
- Parts Used:
- WP33001793
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door Closure broken---Metal piece boken
I took the clamp out of the broken piece and inserted it into the replacement part. I put the replacement into the door and screwed it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Palos Park, IL
- Parts Used:
- 306436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The dryer door would not stay closed.
After 20+ years of service, the plastic part that holds the dryer door closed, broke. I orderd the replacement part on a Monday and received it on Wednesday!
By applying constant pressure with my thumb, the replacement part 'snapped' into place - all of 4 seconds.
Fast delivery of parts and fast instal, made for a great day.
By applying constant pressure with my thumb, the replacement part 'snapped' into place - all of 4 seconds.
Fast delivery of parts and fast instal, made for a great day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Oak Lawn,, IL
- Parts Used:
- 306436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken door latch (receiver)
removed old broken piece with screw driver and pliers...
replaced with new part with thumbs as pushers.
replaced with new part with thumbs as pushers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Avon, CT
- Parts Used:
- 306436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Dryer door wouldn't stay closed
Took 2 screws out of the bottom of the dryer so the front face plate came off. This allowed access to the door latch catch, which was easy to pull out with pliers. Pushed in new latch catch until it "popped" into place. Easy, easy, easy!
Was this instruction helpful to you?
Thank you for voting!