MHE15PDAGW Maytag Dryer - Instructions

I took out the old worn out part and replaced with the one I order.

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

After taking apart the machine (applianceaid.com has slideshows for most major appliances - very comforting and reassuring - highly recommended), I used a shop-vac to clean up all lint and dirt. After getting the retainer ring off the drum roller shaft (snap ring pliers highly recommended), I replaced the drum roller along with the glides which were completely worn through (rivet gun required). I reassembled the dryer to find that the drum wouldn't turn, so I placed another order for the other drum roller and replaced the belt too. Back in business.

looked at video on your web site my wife and I decided to try it ourselves we are 70 and 71 And I am in a wheelchair just had surgery so we ordered parts. received parts looked at repair video a couple of times and went for it. during process we had some moments of frustration but we went back to video. end result, screech is gone. could not have done it with out video thanks.

Was extrememly simple. Just unscrewed the two screws at the bottom front of the dryer and pulled the front of the drayer out. PUshed the broken catch out and snapped the new catch in place. Reattached the dryer front with the two screws and was done. Less than 15 minutes.

I only had to replace the inside one
I pulled the old one out .
And snapped the other one in

used needle nosed pliers, squeezed the latch pop up push new one in. very simple anyone can do it

I unscrewed the door catch and pried out with some resistance the strike part. Screwed in the catch and pushed in the strike. Closed door. Voila!! Back in business with assurance.

I followed the video instructions which were excellent. Dryer repair was a cinch.

I took the front door off, then i took the the front facing off so i could see in where the idler pulley was. Then I took a couple of screws out so i could get the tumbler out so i could put the belt back on track. I replaced the pulley and then started putting everything back together and now the dryer works like a brand new one. I loved buying parts from here. Cause you are showed how to replace the parts you are wanting to replace. I was very satisfied with everything.

Replaced the heating element and both thermostats. Hope that takes care of problem! You tube was a tremendous help through video's.h

The video from this site is perfect. Unplug dryer, remove front panel, unclip wires, remove next panel and pull the drum out. Replace drum support wheels using snap ring pliers (buy the pliers with changeable tips because the holes in the snap ring were pretty small on mine). Put it all back together. The trickiest part is getting the belt back on...just be sure it's not in the groove around the drum and pay attention to how to get it on the motor wheels. Good luck!

First I removed the two screws on the front panel that hold the element in place. I then pulled the element out about 3" and disconnected the two wires. Find out the roller broken. Place an order with Partselect from friend recommendation. Fast delivery, replace the broken roller, reverse the process and test the sound of the dryer. Very satisfied with the parts. Thanks!

Found out you shouldn't try to dry heavy hiking shoes in a dryer....it tends to break off plastic baffle.

The repair directions on PartSelct.com made this repair a piece of cake.
Just removed screws holding door and front of dryer.
With these removed it was a simple matter to detach top and get access to internal components.
Two hex screws held baffle in place.
Total repair took about 15 minutes, but while I was in there I cleaned out all the dust from inside of the dryer and heater unit.
I also reversed door to make it easier to transfer clothes from washer.
The instructions, detailed drawings and the quality of the part were all excellent.
They had replacement to me in 1 day.
Will definitely use PartSelect again.

First thing to do. . . . Unplug the machine. After that, remove the top 2 screws from the cover from between the washing machine and the dryer and remove cover. Then remove the 2 screws from the top of the front dryer cabinet, pull front cover out slightly and gently let it lay forward. From this point, you can look in and see the drum rollers. Behind the rollers on the roller shaft is a 1/2" nut. Use a 1/2" gearwrench to remove the nut, and pull the shaft with roller attached out forward. Use snap ring pliers to remove snap ring, take off old roller with bushings, and replace with new. To re-install shaft with new roller, you will have to lift the drum slightly to give yourself enough room. Re-assemble the front of machine (note: be careful of the wiring on the control panel, as some connectors may have pulled loose. Make sure they are all connected before replacing front of machine). Plug machine in and test it out. While you have the machine open, use a good vacuum cleaner and remove the lint that you will find inside the machine. Depending on how old the machine is, you should find quite a bit.