DG612 Maytag Dryer - Instructions

I suspected a faulty igniter and disconnected the cable to the igniter and measured the resistance of the igniter and found it to be 70 ohms then I checked the voltage at the same cable towards the power source and found it to be 25 volts ac which should be 120 volts ac. Next I checked the radiant flame sensor and found it to be open (it should be a closed circuit when cold). I removed the flame sensor (with the power off) using a small box wrench and found a broken lead. Replacing the flame sensor solved the problem.

I set the dryer on its back to make alignment of the front drum guide cover easy to reinstall in the seal after completion. I removed the 2 screws at the bottom front then removed the white and yellow wires to the interlock switch and set the front cover aside. I then removed the 4 nut screws holding the front drum cover and removed. On the back side there are two teflon and cork "bearings". I had ordered two even though only one was worn down to metal. On each one I then removed the two rivets by drilling them out. Then I placed the corks into the bearing slots with a little glue then inserted the teflon into the slots and riveted them into place with the rivets that came with the kit. I replaced the drum cover, connected the switch and screwed the dryer front cover back on. I set the dryer back up. Connected the vent hose and turned the dryer on. Beautiful sweet smooth and quiet operation. I had replaced the front and back drum seals a few months ago and saw the teflon was missing but did not have the kits at that time. With a complete job I would recommend replacing the front and rear drum seals and the two teflon/cork bearing kits at the same time.

This was pretty much as easy as most other folks had described on this site.
1. Removed the two screws at the front bottom that are holding on the fromt panel, and then lift up and remove the panel.
2. Disconnect the door-open-safety-switch, remembering which color of wire goes on which connection.
3. Remove the four screws (two on each side) on the front bracket that supports the drum and tthat contains the front glides.
4. Remove support bracket and lint trap, letting the drum rest gently on the stuff underneath.
5. Remove the screws holding the lint trap to the support bracket. (My model had five screws.) Remove lint trap from support bracket.
6. Drill out the two pop rivets on each of the two glides, noting the orientation of the teflon pad and mounting strip.
7. Secure - and here is where I had a little problem - new glides in place with pop rivets. (I hadn't use a rivet gun in a while, so I messed up the first pop rivet and had to go to the hardware store to get a replacement. I didn't hold the pop rivet in all the way while I was accuating the gun!)
8. Reverse the process for assembly, and you are all done.

It's simple.

Took everything apart, replaced the igniter flint, and still didn't get heat. Then found out the thermal sensor wasn't running a electrical current through it with voltmeter and just replaced that, now it we have heat again!

Removed lower front cover of dryer, located coils, removed old coils by disconnecting the wires and removing the hold down bracket screws. Pulled the old coils out replaced them with the new coils by aligning the index pins on the coils with the holes in the bracket then reattached the bracket and plugged the wires into the new coils. Then closed the cover on the front of the dryer. Dryer now ignites and stays on to heat up and dry clothes.

Replaced both Coils. Purchased M Series coils much less expensive buying coils together instead of seperately. Problem solved.

Old latch and door striker were pried out with a flat blade screwdriver. New components popped right in. Repair was less than two minutes.

Shut off gas removed gas valve. Removed the coil retainer and installed the new coils. Reinstalled valve and checked. Found dryer worked fine.

Remove back panel n u can see the sensor and easy to replace thanks to the print out i was provided love this website

My dryer stopped producing heat and everything else was working fine. I did some research on this site and others had the similar problem pointing to the ignitor going bad. I needed to determine which ignitor fit my dryer. What I learned is that some of the parts come with a series number and you need to know which one matches your serial number. My serial number started with 40 and I had a choice of buying the part for a series 10 or 60 series. In my case I needed to buy the 10 series since you either go with the same number as your serial number or lower, never higher. When the part came in I removed the dryer door by removing the 2 screws. I then removed the 2 screws on the opposite side of the door. Once the 4 screws were removed I was able to take the front cover off. The ignitor was on the right side and easy to get to. I unplugged the ignitor and used my socket set to remove the bolt. Once removed I vacuumed the lint in the dryer and installed the new ignitor carefully not touching the black area of the part. I put the front cover back on, put the door in place and put all 4 screws back in place. I started the dryer and it was fixed! This was an easy job to repair that saved me money.

I had an issue where I was not getting any power to my ignitor. After replacing the ignitor with a fresh one, the problem persisted. Next, I went hunting all the fuses and therrmostats for continuity. All seemed fine. So finally I decided to jump the flame sensor which is located on the outside of the flame tube. WHALLA! It ignited the glow plug. So with one 1/4"" nut driver I removed the single bolt from the unit, then I used a pliers to remove the two wires from the old unit. I replaced the sensor with Tue new unit and all was well. It took less than 5 min once I diagnosed the problem.

Shut off or unplugged dryer for safety.

Slipped thin blade putty knife up under bezel of switch to unlatch from the panel and pulled forward to remove the swwitch from the dryer. Unplugged the quick connect terminals (3) from the old switch and plugged them onto the new switch. one of the terminals had gotten quite hot and darkened the insulation so it was replaced with one that was supplied with the switch. that was a cut, strip, crimp process. Placed the new switch into the panel and snapped into place.

I had a repairman come by to take a look at my 20+ year old dryer because it wasn't working properly, NO HEAT. He said it was the cycling thermostat and wanted to charge me $190 to fix this problem. He left me the paperwork for this diagnose and charged me $49.50 for looking at the dryer. I called a friend of mine and told him what the repairman had said. He went into your website and found the part, the first time around we ordered the wrong part. No problem, I sent the wrong part back and reordered the proper one. It took him no more than 20 minutes to install this part. I received credit for the wrong part within 2 weeks. The dryer is working great. It’s good to know of a company that still can provide you with parts for a dryer as old as mine, thanks. It worked and it' still working!

Followed advice from here; unplugged machine from power source, removed two phillips head screws located just out of sight below the little indentaion on the front panel, removed front panel & set aside the machine. Unclipping the door switch wires allowed for enough slack so that they didn't need to be disconnected. Unscrewed (or un-hooked, don't remember) the lint box, pulled the drum out slightly, removed the belt, pulled drum out all the way & set aside. Removed the snap rings & wahsers from the idler wheels, removed wheels, put a light coating ot synthetic grease on the shafts & in the idler bushings, re-installed idlers, washers, & snap rings. Re-assembled in reverse order of assembly with alittle difficulty iin getting the new belt in the proper configuration. Removed small access panel in rear of machine to assist in installng the belt finally realizing that the belt DOES NOT go in the indented area of the drum, but on the larger diameter of the drum itself. Tested by rotating by hand, re-assembled front cover, plugged it in & dried the laundry......QUIETLY!

Removed front cover, removed housing cover, took old fan off, installed new fan, put covers back on.
Your instructional video was very helpful. He told which screws to remove to get the covers off. I was unsure about how access the fan until I watched. Well done!