LDG8624AAM Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from Long Beach, CA
- Parts Used:
- WP338906
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
No heat...
Removed and replaced both the thermostat sensor and the ignitor. Tested thej dryer and it worked. Replaced the front panel and it was good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ORANGEBURG, SC
- Parts Used:
- WPY312959, WPY312527, WP6-3037050, WP6-3033630, WP315772
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
old was belt stretched and idler pulley gummed up, drum won't tumble a normal sized load
Replaced all the parts per the very good video provided on the website.
I recommend watching the video very closely several times. BE SURE THE BELT IS NOT IN THE DRUM'S GROOVE. The video mentions this very very briefly; I caught it on my third viewing. If your belt is not the correct location, it may still turn the drum for you - and eat the belt up in about an hour.
I recommend watching the video very closely several times. BE SURE THE BELT IS NOT IN THE DRUM'S GROOVE. The video mentions this very very briefly; I caught it on my third viewing. If your belt is not the correct location, it may still turn the drum for you - and eat the belt up in about an hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from WHEELING, IL
- Parts Used:
- WP33002793, 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Flame goes out after 5 seconds.
Tilted dryer back to access the two screws on the front panel, remove front panel, by raising it up 90° and pull the wires off for the door switch, first I remove the one 5/16 self tapping screw That holds the burner assembly onto the bracket, removed the hot surface igniter screw from old burner assembly, attached to new burner assembly, reinstalled burner assembly and also cleaned orifice from gas valve, also while the front cover was off I remove the fan housing cover and vacuumed out all The lint attached to the fan assembly, unit works great again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Sacramento, CA
- Parts Used:
- 279834
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
No Heat sometimes, But for a moment then None
First and Foremost i was told that my problem was with the Thermal Fuse (Fix Ya.com), Then with the little Electrical knowledge I have thought Fuses don't turn on and off,If the fuse was bad i would get No Heat. (Even for a second) Fuses just don't turn on and turn off intermittently,when they go there done! So after a little research i decided to order the gas coil valve. I tilted the top up, two screws on the front panel, took that off and the valves were exposed,(bottom left) two screws too remove bracket then installed new coils on bracket,put back together and I Have Heat Again! NO problems what so ever since new install. I would say having not been for cleaning lint build up inside the machine (been 6 years) the Whole project took me Ten Minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tara from North Canton, OH
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Female End Of The Door Catch Broke
First I put the square female end iof the door catch kit nto the square hole as snug as I could. Then I gently pushed the door against the piece until I heard it click in to place. That's it!! Sooooo simple--
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Memphis, TN
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The dryer door latch was broken.
The replacement part just snapped into place. (The old part had fallen out) It took less than 30 seconds to do the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Oro Valley, AZ
- Parts Used:
- 33001623
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Buzzer didn't work
Unplug dryer--remove back panel of control console--swap out buzzer--cover back--plug in--good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brad from Georgetown, TX
- Parts Used:
- WP33002970
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old lint filter had damaged screen
Took out the old lint filter and put in the new one. Works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Columbia Falls, MT
- Parts Used:
- WPY312959, WP6-3037050, WP314820, 306508, 12001541
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
very noisy, not working properly
Took it apart according to the videos, replaced about all moving parts (almost). Put it back together and still made noise. It turned out to be the blower wheel. Ordered a new blower wheel and installed it. Works great and has mostly all new parts. The website was great!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Fort Worth, TX
- Parts Used:
- WPY312959, WPY312527, WP6-3037050, 12001541
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer tumbler belt broke.
I followed the videos on your website, but had to clean 30 years of dust and lint out in the process. Cleaning took the longest time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Chicago, IL
- Parts Used:
- 279834
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Gas dryer would not heat - pilot lit briefly then went off
Same as others.
1. Unplug dryer from power source
2. Use nut driver to remove two front screws at bottom of dryer
3. Disconnect cable connected to Secondary Coil (this is the coil towards the rear of the dryer)
4. Use angled phillips screw driver to loosen screws holding cap on top of the two coils. (Angled tool not required but seemed easiest to me)
5. Slide top cap back towards lock screw to allow coil to be lifted out
6. Remove and replace secondary coil
7. Replace cap, tighten screws to lock in place, reconnect cable to coil
8. Restore power to dryer, test and confirm gas flame stays lit
9. Replace lower front panel on unit
PartsSelect a great resource to use for home repairs like these. My first time using site and doing this type of work, now PartsSelect my first source to go to on such items.
1. Unplug dryer from power source
2. Use nut driver to remove two front screws at bottom of dryer
3. Disconnect cable connected to Secondary Coil (this is the coil towards the rear of the dryer)
4. Use angled phillips screw driver to loosen screws holding cap on top of the two coils. (Angled tool not required but seemed easiest to me)
5. Slide top cap back towards lock screw to allow coil to be lifted out
6. Remove and replace secondary coil
7. Replace cap, tighten screws to lock in place, reconnect cable to coil
8. Restore power to dryer, test and confirm gas flame stays lit
9. Replace lower front panel on unit
PartsSelect a great resource to use for home repairs like these. My first time using site and doing this type of work, now PartsSelect my first source to go to on such items.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eli from North Stonongton, CT
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door would not stay shut
Took off the four screws to get to the female clip and used pliers to squeeze it out. Next was using pliers to pinch out the male connector and place the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jim from sierra vista, AZ
- Parts Used:
- Y303836
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Blower fan came loose and broke
No manual on this so had to remove about 12 screws to figger out disassembly,after locating the right ones[front]the job was easy.Remove front plate,remove drum bearing,remove blower front cover,remove snap ring,remove broken fan,clean fan shaft,slide new fan onto shaft[there is a flat in the bore of new fan]instal fan retainer on stub of fan,reinstal snap ring,reinstal the rest of the parts,test drive system[all sat]The part was exactly as ordered,thanks,Jim Thompson
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from LARAMIE, WY
- Parts Used:
- LA-1003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Broken Catch
Watch the video. Very, very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- M. Lyn from Arkansas City, KS
- Parts Used:
- WP33002970
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint filter screen torn
Inserted new lint filter...one second! No tools needed. Price excellent!
Was this instruction helpful to you?
Thank you for voting!