MLE15PDAYW Maytag Dryer - Instructions

Followed the directions of the video and all went smooth. Cleaning the lint and parts was the more time consuming than the actual repair. 30 minutes for the repair and an hour for the clean. All and all very easy.

repairmen said to buy a new dryer! or replace the motor! DO NOT EVEN THINK ABOUT IT!

It was the spring washer that was rubbing against the metal that was causing the very loud noise. The fiber washer that is used on the shaft on both sides of the roller had worn though and allowed the metal-metal contact. The fiber washer wore out! The fiber washers are very cheap!!!! in comparison to a motor or new dryer!


The drum rollers that support the rotating drum eventually wear out the fiber washer.
UNPLUG THE DRYER, DISCONNECT THE VENT
Remove the two screws on the lower front of the dryer panel, probably after you have tilted the unit backward. Remove the front panel by tilting out the bottom as there are two clips at the top. AFTER DOCUMENTING the CONNECTIONS - Disconnect the wires from the switch which is mounted on the front panel.
Carefully put the dryer on its back - be careful of the dryer vent to avoid damaging your floor or dryer vent!
Carefully pull the dryer drum up out of the dryer - as this is done the belt which moves the drum will fall away from the drum. I suggest before you remove the drum to eyeball the way the belt is tensioned and wrapped around the motor driveshaft, guard and tensioner. This will be the most difficult part of reassembling the machine. Some visual understand, maybe even pictures will help you later to get it installed correctly back into proper position... and it is NOT intuitive!
Once the drum is removed, the rollers are accessible. Rotate each and find the squeaker!
I recommend you replace the fiber washer on both, even though only one may be squeaking at this point (the other will be close to being worn out as well!).
I will not document the replacement of these parts as the assembly seems well documented elsewhere. I suggest you remain using the spring washer if there - as the after factory replacements do not seem to provide spring washers.
I would also suggest replacing the dryer drum belt, it is worn, after this many years, and putting in a new one will keep the dryer running for many more years. KNOWLEDGE IS POWER - USE IT

Read the instructions included with the parts, removed the 2 screws on the front of the dryer. Removed a couple of wire connections and 4 screws that held the drum in place. Moved the drum enough to have access to the roller supports. I removed the nut from the back of the supports with a 1/2" wrench. Placed the new supports on the old support pins and reinstalled them. Put it all back together. Probably the most difficult task was getting the drive belt back on the drum correctly. I was done in just over 1 hour.

Unplugged the dryer (don't forget this step guys!!!)

Pulled the front off the dryer (4 screws) and swapped the motor out - take off the belt, pull the blower wheel (by removing the snaprigs and squeeze collar), then pull off the motor retaining clips... unplug the motor and install the new one in reverse. Took me less than 2 hours and my dryer works like new.

WAY CHEAPER than a new dryer!!!

Changed motor

I followed the YouTube video for pulling the heating element to remove and place the thermostat. The actual thermostat removal and replacement was pretty simple. Most of my time was spent removing the front panel, pulling and reinstalling the heating element.

Moved the front door/panel two screws at the bottom of the panel.Then removed the front plate and support for the drum assy. four screws.Then loosen the belt and removed the drum assy. to get access to the drum roller to the back top right,.Used snap ring pliers to remove the clip cleaned the shaft an installed the new roller with the fiber washers and installed per instruction from your video,Also replaced the belt and put all items back in reverse order.It worked like a champ so easy,I would recommend your web site and videos to any one who wants to do it yourself. I have used you in the past and will continue using you for other items for parts and support.

Followed the video. Hardest part was getting the belt around the ideler pulley and motor pulley without seeing. But I got it! Thanks to this site you rock!

Removed front of dryer, removed inner cover, slid roller belt off of drum to remove drum. Only tricky part was the two clip rings. My pliers had .070 tips and the ring holes were smaller so I had to run to HD to buy a pair with various size tips, ended up using the .047 tips. Only one wheel was squeaking when I rotated them by hand, but I had ordered both as recommended here so I replaced them both. Put everything back together feeling the belt to make sure it was not twisted and rolled smoothly when I rotated the drum by hand. Works great now. Lots of thanks to this site and all the posters who share their info!

I watched a video on YouTube for the disassembly of the dryer. The parts replacement took less than 20 minutes; the rest of the time was spent on disassembly and reassembly.

I use U Tube watched Video, you have to take apart the dryer, but pretty simple to do. The drum rollers were very easy to install, make sure to have snap ring plyers, installing belt was easy too, make sure to put it back on it the way it came off, mine was ribbed side down on drum. Take a picture if necessary. Getting the belt on the pulley right is the most important part, the rest is just reassembling,

First thing to do. . . . Unplug the machine. After that, remove the top 2 screws from the cover from between the washing machine and the dryer and remove cover. Then remove the 2 screws from the top of the front dryer cabinet, pull front cover out slightly and gently let it lay forward. From this point, you can look in and see the drum rollers. Behind the rollers on the roller shaft is a 1/2" nut. Use a 1/2" gearwrench to remove the nut, and pull the shaft with roller attached out forward. Use snap ring pliers to remove snap ring, take off old roller with bushings, and replace with new. To re-install shaft with new roller, you will have to lift the drum slightly to give yourself enough room. Re-assemble the front of machine (note: be careful of the wiring on the control panel, as some connectors may have pulled loose. Make sure they are all connected before replacing front of machine). Plug machine in and test it out. While you have the machine open, use a good vacuum cleaner and remove the lint that you will find inside the machine. Depending on how old the machine is, you should find quite a bit.

The video from this site is perfect. Unplug dryer, remove front panel, unclip wires, remove next panel and pull the drum out. Replace drum support wheels using snap ring pliers (buy the pliers with changeable tips because the holes in the snap ring were pretty small on mine). Put it all back together. The trickiest part is getting the belt back on...just be sure it's not in the groove around the drum and pay attention to how to get it on the motor wheels. Good luck!

I followed the video instructions which were excellent. Dryer repair was a cinch.

I made the mistake of repairing my old maytag neptune dryer with cheap eBay rollers and they crumbled apart and made a ton of noise within a month. I replaced them with quality OEM parts from partselect.com and my dryer is running like new. It's easy to do with common household tools and there are even easy to follow instructions available online.