MUE15PDAZW Maytag Dryer - Instructions

Watched video then followed directions in the package. Installation wasn't difficult but it would have been easier if I had a set of snap ring pliers (cheep at Harbor Freight). I was surprised by the amount of lint buildup. I feel much safer now that everything is nice and clean. Clean and quiet, worth the time to make the repair.

Remove front of cabinet, hinge the top back, remove the drum and drive belt, unplug the motor, remove cover on blower, remove snap ring on end of motor shaft, remove motor mount hold-downs, remove and replace motor in reverse order

Read the instructions included with the parts, removed the 2 screws on the front of the dryer. Removed a couple of wire connections and 4 screws that held the drum in place. Moved the drum enough to have access to the roller supports. I removed the nut from the back of the supports with a 1/2" wrench. Placed the new supports on the old support pins and reinstalled them. Put it all back together. Probably the most difficult task was getting the drive belt back on the drum correctly. I was done in just over 1 hour.

I had to remove the door first. Then the retaining brackets that hold the upper lid on. This also allowed removal of the front cover. After releasing the tension of the drum belt, I removed the drum and replaced the drum roller in suspect. Installation was reverse in order. Don't know why I waited so long to do such a simple job.

I removed the lower panel and control panel, then the front body panel. With those open, I removed the drum support and drum. I then removed the cover from the air guide, then unbolted the air guide from the motor assembly.

Then, I disconnected the wiring connector to the motor, unbolted the motor carrier from the bottom of the unit, and removed it. I removed the idler arm from the motor carrier, then unclipped the two clips holding the motor in the carrier.

At that point, while everything was out, I gave the carrier a thorough cleaning. I then placed the new motor, replaced the clips that hold it in place, and put everything back together in the reverse order of taking it apart.

While I was in the machine, since I had everything taken apart, I did also take the opportunity to replace the idler pulley and drum rollers proactively.

My son did the repair work. He took off the door and then carefully unhooked the belt and removed the drum. Replacement on the drum roller kit went smooth, and he then oiled the idler pulley while he was in there. I now have a "quiet dryer" once again!!! Had orderd the wrong part to begin with, but was very easy to return, receive my credit and get the "right" replacement part.
Great Service!!!!

Removed the door then removed front panel then removed 8 screws that held the drum in. At this point reached in and removed the snap ring on the wheels and replaced the washers and wheels. Then reassembled it.

The video from this site is perfect. Unplug dryer, remove front panel, unclip wires, remove next panel and pull the drum out. Replace drum support wheels using snap ring pliers (buy the pliers with changeable tips because the holes in the snap ring were pretty small on mine). Put it all back together. The trickiest part is getting the belt back on...just be sure it's not in the groove around the drum and pay attention to how to get it on the motor wheels. Good luck!

Found out you shouldn't try to dry heavy hiking shoes in a dryer....it tends to break off plastic baffle.

The repair directions on PartSelct.com made this repair a piece of cake.
Just removed screws holding door and front of dryer.
With these removed it was a simple matter to detach top and get access to internal components.
Two hex screws held baffle in place.
Total repair took about 15 minutes, but while I was in there I cleaned out all the dust from inside of the dryer and heater unit.
I also reversed door to make it easier to transfer clothes from washer.
The instructions, detailed drawings and the quality of the part were all excellent.
They had replacement to me in 1 day.
Will definitely use PartSelect again.

First I removed the two screws on the front panel that hold the element in place. I then pulled the element out about 3" and disconnected the two wires. Find out the roller broken. Place an order with Partselect from friend recommendation. Fast delivery, replace the broken roller, reverse the process and test the sound of the dryer. Very satisfied with the parts. Thanks!

Replaced the heating element and both thermostats. Hope that takes care of problem! You tube was a tremendous help through video's.h

Remove the door and front cover ,then the top flips up ,remove the front drum support then the drum,remove the snap ring and the pulley

First thing to do. . . . Unplug the machine. After that, remove the top 2 screws from the cover from between the washing machine and the dryer and remove cover. Then remove the 2 screws from the top of the front dryer cabinet, pull front cover out slightly and gently let it lay forward. From this point, you can look in and see the drum rollers. Behind the rollers on the roller shaft is a 1/2" nut. Use a 1/2" gearwrench to remove the nut, and pull the shaft with roller attached out forward. Use snap ring pliers to remove snap ring, take off old roller with bushings, and replace with new. To re-install shaft with new roller, you will have to lift the drum slightly to give yourself enough room. Re-assemble the front of machine (note: be careful of the wiring on the control panel, as some connectors may have pulled loose. Make sure they are all connected before replacing front of machine). Plug machine in and test it out. While you have the machine open, use a good vacuum cleaner and remove the lint that you will find inside the machine. Depending on how old the machine is, you should find quite a bit.

first, i removed two screws at the bottom of front panel. then lifted from the bottom removing it. next, removed drum surround and drum. next , removed right roller and roller shaft. then installed new shaft, slide roller back on shaft. next reinstalled drum, drum surround and front panel. Now so quiet you can hardly hear it run, also my sister says it drys much faster.

I only had to replace the inside one
I pulled the old one out .
And snapped the other one in