MDE3600AYQ Maytag Dryer - Instructions

Went smoothly. Took the opportunity to vacuum out entire cabinet. Also removed tumbler vanes inside dryer as coins had made their way into them. The only other suggestion I have is that I didn't notice cabinet screws were different lengths till I started reassembly. Might be smart to label and separate them

At first I thought I could just replace the pulley, but on closer inspection I found that the pulley had become seized on the shaft. I ended up removing the entire bracket (which I should have purchased also) and cutting the shaft off. I manufactured a new shaft from a bolt of the appropriate size and tack welded it to the bracket. It took a little more time than I anticipated. My advice to anyone doing this would be to spend a little extra money and buy the entire bracket and pulley. That would make this about a 15 minute job.

Disassembled dryer and replaced drum support roller and shaft. That took care of the noise but I still replaced the belt and idler pulley while I had it apart.

Removed door, then brackets holding top panel to side exposed after removing door. Lifted top panel to expose dryer chamber. Rotated chamber to access outside screws holding broken baffle. Removed and replaced baffle. Closed top lid, reattached to side. Replaced door. When reattaching top lid, do not tighten H/W just yet. You'll have to maneuver the hooks into place for the door to reattach. Then tighten when in place.

Door switch was very easy to replace as it simply snaps in for the outside and you just clip on the two control wires that already have clips on them.

All you need for a Maytag is a snub nose Philips screw driver. The screws on the front panel are at the bottom angled down, so a regular length Phillip's won't work. Just unscrew the 2 screws, then lift the panel up and out. Careful not to pull out too far, there are 2 wires attached to the switch. The replacement switch is NOT an exact copy of the old one. My Maytag is over 30 years old and it only had 2 prongs on the switch. The new one has 3. Don't let that throw you. It is the same size. Just attach, 1 wire to the bronze connector & the other to the silver. Push the switch into the door opening, re-attach the door. Total time 20 minutes. Saved well over $100 in a service call. Anyone with an IQ above freezing can do it.

The dryer model was on a sticker inside the door which had long ago rubbed off. The most difficult part was figuring our how to dismantle the dryer. I finally looked up the matching washer by model number watched a youtube video and the dismantle was the same....take off the door, remove front cover then remove screws that held the hook brackets that held the top down. After we figured that out the rest was pretty easy. The main issue was the Idler Pulley Wheel and Bearing. We decided to replace the rest of the parts because we already had the thing all apart. It is amazing all the lint that gets into the dryer cabinet and passed the lint filter. Dryer works like new again. I love this set and will keep repairing as long as we can get parts.

Replaced damaged parts and recommended parts normally causing the problem. Dryer is working again like new. I expended $112 rather than $600 for a new equipment. Good deal!

The dryer started making a screeching/squealing noise…when it became unbearable, I decided to research the problem and found this website - it was tremendously helpful.

Based on what I found, I decided to order two drum rollers and two shafts – hoping that would solve the problem. My husband and I disassembled the dryer and replaced those parts. We also vacuumed the unit and wiped down the 10 years of gunk. Honestly I am surprised we have not had a fire given the amount of dust/lint inside the unit. I also took the opportunity to give the vent a good cleaning as well.

We put the unit back together, turned it on and listened to the quiet hum of our renewed dryer. Until about 15 minutes later and then the screeching/squealing started again. Kicking myself for not ordering the idler arm and shaft as well as the idler pulley wheel and bearing the first time – I went online and placed another order.

We took the unit apart a second time. We did inspect the pulley the previous time, but it appeared in good working order. Not seized like some of the other posts mentioned. Upon further inspection, it did seem to make a squealing noise when we wiggled it – duh!

The unit was put back together, quietly doing it’s job and we feel confident that we will get a few more years out of it. The videos were extremely helpful as were the posts from other do-it-yourselfers. We saved a lot of money with this fix.

Good luck!

BTW - The Lint Filter was not a problem - I just thought after 10 years, we could use a new one. I laughed when I saw the repair video on it!

i removed the 2 screws holding the door hindges on. then i removed the 2 adjasent screws to remove the front door panel. i rotated the drum to aceses the screws holding the baffle and installed the baffle .

I had replaced belt, but the noise continued. Ordered new rollers and washer. Removed the front panel by tipping the dryer back against the wall and removing two screws at the bottom of the panel. Tipping the dryer makes it easy to remove the front panel. Removed the front drum support by removing four (4) screws. I was then able to just move the drum enough to have access to the rollers. Didn't even have to remove the belt. Replaced the rollers. Needed special pliers to remove and replace the retaining rings. Put the drum back into position and mounted the front drum support. Tightened four screws and then put the front panel back on. Plugged it in and tested it. Problem solved. Took about 35 minutes. Thanks

To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.

I removed the cover and pulled out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.

Per instructions I printed off online: took off door, then the front panel. Pulled out the old switch/button, connected the new switch/button, made sure the new button was working; put the panel back on then the door and DONE!

I was able to quickly make this repair with the help of some instructions that I found on this site on how to remove the front panel of my dryer. 4 screws on the front around the door (and removal of the door) and then it was simply a matter of rolling the top portion out to pop it out of some clips and then the front panel opened toward me and I was able to lift it off of the metal fingers that secure it on the bottom. Removing the old baffle was a matter of removing two screws with a nutdriver and installation of the new baffle was a breeze. All in all I was done start to finish in under 10 minutes.

Just took the old one out and put the new one in! Fit perfectly! Very happy with your service and part came super quick!