MDG4000AXW Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- keith from saluda, VA
- Parts Used:
- 33001809
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Dryer continuously running, no timer advance, dampness indication stayed on "wet"
Took 3 screws out of the back of the back of the machine and tilted the control panel houseing forward. Slid the module free of it's track and unplugged the bundled wiring plug. Plugged new module, relpaced in is slot and put the control panel back in place
Was this instruction helpful to you?
Thank you for voting!
After the first flame the flame would not come back on
Turned out to be the primary coil on the gas valve. If you remove the cover of the coils and wait for the dryer to try to start the flame the coils are energized, a magnet is turned on. By lifting the coil you should feel the magnet if the flame is on. If the flame does not come on after the ignitor fires check to see if the coils are energized. If not buy the set, it's cheaper then purchasing them separately.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from pleasant valley, NY
- Parts Used:
- W10169313
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
door switch broke
remove bottom section under door 2 screws remove door 2 screws remove switch by squeezing tabs install 2 new female ends on wires supplied with switch . put switch back in plug in wires .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from CAMBRIDGE, MN
- Parts Used:
- WP33001762, W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Will not start all lights on,makes a ping sound on the control panel when you push the start button
Replaced thermal fuse and replaced door switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from Missouri City, TX
- Parts Used:
- WP33001621
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Our timer dial had been broken for some time, cracked around the connection to the control panel. I had been able to epoxy glue it to where it was functional, but that eventually failed. We were using a pair of pliers to set the timer on the dryer.
I was able to easily find the replacement part on PartSelect, and the schematics showed me how to easily disassemble my dial (which has three parts) so that only the broken part needed to be replaced. I used a tiny straight-slot screwdriver to pop the pieces apart. Once we received the new piece, it was very simple to pop the pieces back together and have a fully functioning new dial!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Warsaw, IL
- Parts Used:
- W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door safety switch would not close keeping dryer from running
Shut off or unplugged dryer for safety.
Slipped thin blade putty knife up under bezel of switch to unlatch from the panel and pulled forward to remove the swwitch from the dryer. Unplugged the quick connect terminals (3) from the old switch and plugged them onto the new switch. one of the terminals had gotten quite hot and darkened the insulation so it was replaced with one that was supplied with the switch. that was a cut, strip, crimp process. Placed the new switch into the panel and snapped into place.
Slipped thin blade putty knife up under bezel of switch to unlatch from the panel and pulled forward to remove the swwitch from the dryer. Unplugged the quick connect terminals (3) from the old switch and plugged them onto the new switch. one of the terminals had gotten quite hot and darkened the insulation so it was replaced with one that was supplied with the switch. that was a cut, strip, crimp process. Placed the new switch into the panel and snapped into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Fernley, NV
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Dryer got hot then heat would shut off
Sensor is in the front lower left. Gas off, electicity off. Removed two screws for the filter, pry/lifted the top up and taped it too the overhead cabinet, removed two screws inside top of front panel, lifted pandel with door closed staight off. Two screws to remove the flame sensor braket. unplug the old sensor install the new one and reverse everything. With others suggestions I purchased temperature switches etc. but the radiant flame sensor was the problem. I now have some spare switches for future. Excellent company and very quick service. Oh, Sears wanted 200.00 just for the service call, I live rural.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Madison, WI
- Parts Used:
- 4391996
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Gas dryer not heating
Thank you very much for your prompt service. This was so cool... On Monday night my wife told me the dryer was not heating. I did a basic diagnosis, checked the internet for parts and lowest price and found your site. I ordered the part I thought I may need and 2 days later the part arrived and the dryer is working again.
Way to go, PartSelect!
Way to go, PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hazel from CONNERSVILLE, IN
- Parts Used:
- 12001541
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
noisy
I watched the video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rob from Henderson, NV
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Dryer would only heat at start up for one cycle
Ohmed coils and both had continuity so I changed radiant heat sensor. No bench test for Radiant Heat sensor. Same problem. Changed both coils and dryer works fine. Weak coils were my problem. I read thru the same issues in Parts Select forum and it said Radiant Heat sensor was problem 25% of the time. With coils having continuity and no ohm value specified for coils I made wrong choice but, I have spare parts and look for another 10 years of life in the dryer. Nice to have this forum to research appliance repair. Very helpful for parts location and installation. Dishwasher is next!
Was this instruction helpful to you?
Thank you for voting!
not drying all the way, not getting hot enough
loosened two screws on back of top,lifted top away from front panel.it just lifts off front corners,removed two screws at top corners.lift front panel up and out,this panel supports dryer tub,remove slowly,unplug door switch parts are located left side bottom two screws holding in had to have wife hold drum up to put front panel on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- claude from laguna niguel, CA
- Parts Used:
- 306436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing, probably broken female latch part
Press in the new female latch part with thumbs. Took about two seconds!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Menomonee Falls, WI
- Parts Used:
- WP33001808, 33001799
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
rodent entry through vent,chewed parts,(distroyed).
Removed the door and machine front.replaced old duct assembly with new ,and reassembled front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- karl from monroe, GA
- Parts Used:
- 306436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer would not stay closed.
I used a flat screw driver to pop out the old female portion and snapped in the new one. Dryer stays shut. That's it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Fairfield, CA
- Parts Used:
- MAL9000AXX
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Conversion from natural gas to liquid propane
By following the directions included with the kit it was fairly clear. The diagrams of the control valve was helpful. It would have helped to tell which screws to remove to access the valve and where the screw was that retained the burner assembly.
Was this instruction helpful to you?
Thank you for voting!