MDG11PDAGL Maytag Dryer - Instructions

Turn off circuit breaker or unplug. Remove two screws 4 inches from bottom front panel of cabinet with stubby phillips head. Pull panel towards you about 30 degrees; then wiggle it down, to free two steel spring clips holding it to cabinet. Pull off red and yellow wire from door switch. Now set front panel aside. Blower assembly is facing you at lower left. Open the housing by removing six small screws from cover and one attached to dryer base. Remove spring clip from end of shaft. (A circlip pliers helps to prevent it from springing off somewhere.). Squeeze spring retainer surrounding blower wheel shaft with regular pliers, and wiggle the blower off. Replace in reverse order. Be sure insulation around blower wheel housing seats properly into front panel. This keeps the hot air flowing up past the lint trap.
Easy job, about half hour. Mine took longer, because I had removed the belt and drum, thinking the noise came from bad drum support rollers. It was just the plastic blower wheel shaft seat, which had worn itself round. Cost $20 (including shipping) and my 29-year old Maytag is as good as new--at least for now.

Fallowed instructions on YouTube

Removed front panel and tumbler, replaced roller axle,
wheel, and front glides. Anybody can do this.

Followed instruction video

Removed front cover.removed 4 screws holding drum in place. Cleaned out lint from everywhere. Placed new belt over drum looping it over idler arm & motor pulley. Pushed drum back ; rotated drum to see that belt was engaged. Put front drum bracket in place. Put front panel in place with 2 screws at the bottom. Tested motor & rotation of drum; then checked heat. All worked fine. Took 1 hr. but most time spent cleaning lint.

By watching a video I disassembled the front and took the dryer tub out and replace the two rollers and it took about 60 minute.

I removed the front of the dryer and the drum support plate. I drilled out the old rivets and installed the Glides with the enclose rivets. The Glides came loose in a few days! The holes in the glides are larger than in the old Glides. I disassembled the dryer again and reassembled with my rivets. This time I held the rivet gun inside the perimeter of the dryer so that the head of the rivet is opposite the initial installation. So far, so good, except the dryer still squeaks. The idler pulley is now the culprit. White grease burned up. I reassembled with high temperature grease. If that does not work, I will need another idler pulley. The journal looks very worn. the dryer is 30+ years old.

I UNPLUGGED TH UNIT.Removed the 2 screws holding the front panel in place, disconnected the electrical leads on the panel. These screws are located on each side of the panel 3 in. from the bottom. Removed the 4 screws holding the shroud. Disconnected the ground wire on the shroud & set both aside. Installed the new belt per the diagram & instructions. Turned the tumbler by hand a few times to verify proper installation. Re-installed the shroud & front panel including reconnecting the leads & ground wire. You need to use both hands in a tight space to install the belt on the pulley & guide(a littledificult) The new belt fit perfectly & the instructions were easy to follow & accurate.

After viewing repair video I used those instructions, after removing drum place new belt on drum, I used scotch tape to hold belt in place, tape belt with 2 inch strip about every foot around drum, leave extra belt that connects to drive motor folded down and taped to drum. After installing drum connect belt to drive motor and roll drum to remove tape. This will keep belt from sliding out of place on drum while installing.

Opened your replacement part and found a broken fin on the blower wheel. no way I was going to return it and wait another week for another part. Perhaps you folks need to inspect what you send out. 1 blower wheel with a broken fin and 2 clamps. Replacement was easy and quickly accomplished. Having replaced drum rollers and the belt this dryer is almost new. Thanks

I watched your YouTube video. Access to the interior of the dryer and replacing parts was EASY. Unlike the machines in the videos ACCESS is VERY EASY as only one panel needs to be removed. Access is from the FRONT PANEL and secured by two top clips and two front bottom screws. Just unscrew and swing the bottom up at about a 45 degree angle; the panel comes off and can be placed to the side. I first replaced a thermostat and a coil kit but still no heat. I then ordered a new FLAT STYLE IGNITER ( which I discovered was broken off ) and a RADIANT FLAME SENSOR and these parts FIXED THE PROBLEM. Parts cost about $90 (Dec. 2016) including shipping.

This dryer has been really reliable. This is the first time I've had to repair it. PartsSelect.com says the noise had a 30% chance the problem would be the tumbler rollers and shaft and 18% it would be the blower impeller fan. I took a chance on the rollers, thinking I would save $20 on the blower fan. Big mistake! Once I dissambled the dryer, I realized almost immediately it was the blower fan and not the rollers. When I manually turned the motor shaft, I discovered the problem. The plastic fan's shaft hole is worn to a larger diameter and is semi-freewheeling on the shaft causing the racket. I replaced the rollers and belt and ordered a new fan. I tried putting electrical tape on the shaft to enlarged the OD like a fellow on this site said, but it worked for about 3 minutes then the racket started again. Also, I had to pull the dryer away from the wall and open the access door to the back of the motor in order to thread the drive belt on the motor and idler pulleys. I couldn't fit my arms along side and under the tumbler. I've got the scratches on my left arm to prove it. Suggestion: Replace the blower fan, rollers and shafts if you have the rumbling noise when operating the dryer. Might as well replace the drive belt while you have it apart, too.

Fast receipt of parts from supplier . All parts went together very quickly. Don/t recommend this work for those who have no mechanical skills. realignment of screws can be very tricky . They must all be correctly aligned first and driven in at diagonals to equalize pressure . Job needs to be used with hand tools as it is easy to strip out the threads in dryer by overtightening the screws.
PS before this we had replaced the drum belt.
Update:
We ran the dryer after replacing the drum support rollers and the idler pulley and it was smooth for about 5 minutes. then the rumbling and uneven rotation started up again! The tip-off was when we had done a test roll on the drum after changing the above parts, we heard a rumble from the blower wheel! so we ordered the blower wheel, replaced it and the dryer sounds like new.
Thanks to others who have written their stories which helped us figure out the problem. : ) saves big $$ on buying a new dryer. PS ours is 15 years old and has had heavy use.

replaced

Replaced igniter, then the two coils on the gas valve. I'm not sure which actually fixed the problem as I was not testing the repair correctly. I needed to attempt to dry an actual load of wet clothes.