MLE23PRAYW Maytag Dryer - Instructions

Remove the door and the plastic brackets on the other side of the door opening. Remove the front cover by gentally pulling from the top first. Support the dryer basket (I used an old towel and a block of wood. With a 1/2 inch wrench remove the Roller Shaft with the Drum Support still attached. Replace new shaft and drum support. (always replace both at the same time or you will find that the problem will come back much sooner.) Careful when installing. Make sure that the new non metalic washers (suppied) are propery seated when you are tightening down the nut.

First removed front door 2 screws holding it to frame, then removed 2 screws holding front cover panel on tilt out front panel, used vac to clean inside, removed idler arm with pully attached, replaced with new parts when I did a test run still had a llitle squeek, the drum support wheel on right looking from front making some squeeking,I went back in removed part shaft had small rust spot cleaned with jewelers cloth lubed and wiped off, no more squeek I wish I had ordered new drum wheel when I ordered idler parts, then I could have done a complete overhaul now I know more I have never worked on a dryer before the drawings on the web site heleped a lot

I removed the dryer door and attaching hardware to other covers. Raise the top cover and prop it up. Remove the drum retaining cover and disconnect the door switch wires, making note of their locations. Release tension on idler and take belt off of motor. Pull the drum out with belt still around it. Vacuum lint and dust from inside cabinet. Use snapring pliers and remove the snaprings on the drum rollers. Remove the old rollers and washers, clean the shafts and apply a light film of oil on the shafts. Install new rollers and plastic washers on shafts and secure with snaprings. Remove the "E" clip from the idler shaft and remove the old roller. Clean and lube the shaft and install the new idler and clip. Place the new belt on the drum with the ribs against the drum. Put the drum in place and install the front drum retainer. Position the belt around the motor pully and tensioner. Rotate the drum to get the belt to track. Attach the remaining covers.

We could not find directions for the brand that we have. First we took the back off, which we did not need to do.
lift the top of the dryer, remove the front remove drum. Place belt on front of motor, wrap double belt around support on bottom of dryer, open the remaining belt and stretch around drum. Hold drum in place, replace front and top.
Need at least 2 people, not at all intuitive.

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

I took out the old worn out part and replaced with the one I order.

The video was excellent and made for an easy repair. Would highly recommend.

I ordered the wrong motor for my dryer PN PS3500892, the right one was PN PS11741125, the motor specs were the same but the shaft were different lengths and different blower fan and fasteners. Since I had the wrong motor in hand I worked with Parts Select to order the correct blower fan and fasteners for this motor. Got it all installed and everything fit as it should. even though this was a different part than I had before it saved me $100 by doing it this way, Thanks to Parts Select for helping me through this maze with me asking many questions about part sizes and fasteners. They did this all for my savings. Most parts places would not have gone this far for the customers benefit. Thank you very much Parts Select !

Remove front of cabinet, hinge the top back, remove the drum and drive belt, unplug the motor, remove cover on blower, remove snap ring on end of motor shaft, remove motor mount hold-downs, remove and replace motor in reverse order

looked at video on your web site my wife and I decided to try it ourselves we are 70 and 71 And I am in a wheelchair just had surgery so we ordered parts. received parts looked at repair video a couple of times and went for it. during process we had some moments of frustration but we went back to video. end result, screech is gone. could not have done it with out video thanks.

Several times I watched the video of "Steve" removing the old motor and installing the new one. Pretty much followed what he did. Faltered for a moment at the end reinstalling the drive belt as that was a blind procedure, done by feel. Hardest part was getting the spring clamps off the old motor; even Steve struggled a bit doing that part of the job on the video. But in the end, the dryver started right up and ran quieter than it has for months.

After taking apart the machine (applianceaid.com has slideshows for most major appliances - very comforting and reassuring - highly recommended), I used a shop-vac to clean up all lint and dirt. After getting the retainer ring off the drum roller shaft (snap ring pliers highly recommended), I replaced the drum roller along with the glides which were completely worn through (rivet gun required). I reassembled the dryer to find that the drum wouldn't turn, so I placed another order for the other drum roller and replaced the belt too. Back in business.

I removed the lower panel and control panel, then the front body panel. With those open, I removed the drum support and drum. I then removed the cover from the air guide, then unbolted the air guide from the motor assembly.

Then, I disconnected the wiring connector to the motor, unbolted the motor carrier from the bottom of the unit, and removed it. I removed the idler arm from the motor carrier, then unclipped the two clips holding the motor in the carrier.

At that point, while everything was out, I gave the carrier a thorough cleaning. I then placed the new motor, replaced the clips that hold it in place, and put everything back together in the reverse order of taking it apart.

While I was in the machine, since I had everything taken apart, I did also take the opportunity to replace the idler pulley and drum rollers proactively.

Followed the directions of the video and all went smooth. Cleaning the lint and parts was the more time consuming than the actual repair. 30 minutes for the repair and an hour for the clean. All and all very easy.

I began by removing the two screws at the lower part of the front panel. After removing the panel I was able to access and remove the broken switch which was located on the front panel. I popped out the old switch and replaced it with the new one, reattached the wires and put the front panel on and the jod was done.