MDE9700AZW Maytag Dryer - Instructions

Dryer was real easy to get into, there are two 1/4" screws on top back of dryer that you can take out to take off the top. The elec. control board is on the left front of mach. it takes about 2 or 3 mins. to take out with a screw driver. I suggest that you go ahead and pull front of dryer off and clean it out if possible as the inside of mine was full of lent. There are only 4 or 5 screws holding the front on, the door will come off with front cover. It is also very easy to check all the sensors and the heating element if you have a multi meter. I hope this will help Oscar

You know! I forgot exactly where it was i got the info to fix the problem but, "Parts select" was mentioned. Once I had an idea as to what to do I then, wasted time around town looking for the parts with no results. I then did what I should have at first an ordered the parts from Parts select. got them in the mail, lightning quick! I think I may have found the info here as well,not sure. (this site is awesome None the less) but the info led me to the Thermostat, I then jumped it as indicated and wham!! it ran. Order both the thermostat and thermistor. only problem I ran into was, removing the front display panel. broke some of the retaining clips off in the process. all in all, it was an easy fix that saved me a bunch of dough. greatfull to parts select for a speedy deliverie and to the website that made it possible. think it may have been here at the free repair help, section. awesome and highly recommended thanks!!!

The part came in very quickly. If you know how to remove the front panel, it is very easy to repair. The hard part is to diagnose the problem. The first thing to check is the igniter. If it comes on then you look for faulty limit switches. If you have lots of training in electronics and appliance repair this is very easy, if you do not I would not try this. I have 40 years in the repair business, It still took me 1hr. to find the problem. the switch was intermitted, one time the dryer would work the next time it would not. Good luck and happy repairs.

I just knew it had to be the heat sensor unable to activate the actual ignition. I following the directions and video for the installation of the heat sensor #PS344761. It went very smoothly. Upon completion of the installation, the click, then the flame roared to life and I felt like a real do-it-selfer!! This was short lived. The wetness of the clothes had no effect. Something I did not do and I certainly know better was to check and see what was taking place before I replaced the "damaged" sensor. No, I was just so sure there was no need of that. You say, put the old back in and watch what happens....I recycled the old one immediately. Sigh! We have had two weeks of rain and I'm really tired of damp clothes everywhere. I will read other alternatives and report back. DClark, TX

changed fuse,radiant flame sensor. no help. bought a new dryer. i don't think the gas valuve was opening.everything seemed to be working properly,just no gas.

Followed troubleshooting steps. Checked thermal fuse (shorted)- OK. Checked igniter (about 70 ohms) - OK. checked flame sensor - (open) BAD (should read shorted). This part is normally shorted then opens when the igniter gets hot causing it to open and thus turns on the gas flow. An open flame sensor does not permit the igniter to turn on.

The Maytag dryer had a removable front panel so it took only about 15 minutes to remove the front, replace the blocking plug and orifice and reinstall the front panel. I gave the repair time as 30-60 minutes since I took the time to vacuum the interior and clean the flame sensor. Great instructions were included with the kit.

I read some of the repairs of other people and this best described my situation. I ordered the Radiant Flame Sensor and followed the step by step instructions in the video for the repair, which by the way was excellent. It couldn't have been easier. My most difficult part of the repair was moving my dryer out of the laundry closet.

Since there were no troubleshooting steps, I had to start replacing the items according to the list that showed the parts that have fixed the problem for others. I ordered one at a time until I got the part that fixed the problem. I went through 4 parts before I replaced the gas solenoids which is what fixed the problem. By the time I was done, I could disassemble that dry in about 5 minutes or less.