MDE9700AZW Maytag Dryer - Instructions

remove top of dryer,remove dryer door, then remove front of dryer themostat is in front on exhaust duct has one white and one yellow wire two screws hold it in . Door switch is a push in connection with a three wire connector.

Opened the bottom panel w/ 1/4 nut driver to access the flame sensor and easy fix.

After removing the top (2 screwa) I removed the control panel (4 screws), top support that held the control panel (3 screws), the front pane (6 screws and one wiring harnes) and the internal panel (5 screws and two wiring harnesses) With these removed I loosen the belt by pulling it off of the tensioning pulley and remeove the drum assembly. I took the beltoffof the old drum and reversed the process to re-install the drum. This is the 3rd drum for this dryer,the other ones were replace due to the felt seal failing.

Test thermal fuse for resistance. If has 0 resistance you have a bad fuse. Also check voltage going to wall outlet. Must use at least 600 volt tester. Motor will run on 110 volts, but will not activate heating element. Heating element must have 240 volts to operate. Always make sure you turn off power when working on electrical problems. Be safe and good luck.

changed high limit switch, and sensor grid and thermo fuse

Replaced the flame sensor since it was believed to be the problem contributing to the lack of flame in this gas dryer. However, this part did not correct the problem.

This was a simple repair. Removed the small access panel where the vent pipe comes through, the roller is right there. Unscrewed the support roller bolt, looking for all the pieces that had broken and fallen inside the housing of the dryer. Using the washers and nut from the old one, put the new roller in place, be aware that you have to lift the drum a little bit to get this new roller in. It could take two people depending on your strength. Tightened down the roller, spin the drum by hand to make sure it was ok, then put the access panel back on and fired it up for a test run.

I had a problem a couple of months ago with the dryer not heating and replaced the thermal fuse after checking the the parts with a voltage meter and the dryer worked fine. When I did the repair I also cleaned all the lint out of the dryer, exhaust, and the vent. It worked fine. A couple of weeks ago my wife commented about how hot the dryer was and it seemed unusual. I realized there was another problem but before I could check it, the dryer stopped heating again. Some time ago, the sensor dry funciton quit working so I just went ahead and changed all the electronic componets, the two on the exhaust tube and the two on the heating tube. I assumed the high limit thermostat failed. After unplugging the dryer, I took the two screws loose on the top backside of the dryer that hold the top in place and removed the top, sliding it back. I removed the four screws holding the control panel in place and rotated the panel forward, then up and out of the way. I removed the four screws along the top of the front panel, then the ones from around the opening on the front, and the front door. There was one screw that held the heating tube. I removed it and the tube slid forward. I took the front wire lose and rotated the tube clockwise to pull it out and took off the back wire and changed out the thermal fuse and thermostat. The exhaust tube was right there in the front and all I had to do was change out the parts on it. Everything went back to gether as easy as it came apart and when I plugged the dryer back in, it worked just like new.

Replace the igniter and dryer did light and after 3 minute went out. so I ordered to gas valve selenoid's and replaced those and everything it working properly

Unplugged electrical cord to dryer. removed the front cover 2 screws on the bottom. Lifted front cover off. Unplugged the 2 wires going to the old flame sensor. Used nut driver to remove 1 screw holding the flame sensor in. Removed old sensor replaced with new one. Reattached the 2 wires back on to the new flame sensor. Tested. Flame stayed on longer! Dryer works great dryer is 20 years old and still running like new now. Part was the exact match I needed.

On the Amana dryer, I had to remove the top panel. then the front panel to access the burner assembly. I also had to remove the gas pipe coming to the burner, because I replaced the tube burner assembly at the same time. There is only one screw that holds that back end of that gas pipe. The thermal flame sensor is on the left side of the burning chamber, with only one small Phillips head screw. just remove the 2 wires, keeping track of which terminal they belong. Just twist the sensor out of the small slot, and out it comes. The tube burner assembly is fastened with 2 screws. The entire burner assembly comes out in one piece, but be real careful not to bang the igniter when removing it. The coil assembly has 2 wires, which you cannot get wrong, because one has 2 prongs, the other has 3 wires.The local repair shop wanted 90 bucks per hour, plus parts, and I installed both the burner tube and radiant flame sensor for around $80.

Followed the easy to understand how to video. The drier was up and heating again in less then 30 minutes.

Unplugged dryer from power source, used putty knife to release latches that hold top on, tilted the top out of the way, unplugged door lite, located the radiant switch, removed 1 screw,then undid 2 wires & lifted out switch. Reversed procedure plugged in dryer....wa la had dried a large load of clothes, took 1/3 the time to dry clothes at last. Thanks "PartSelect"

I verified that the thermistor was bad by testing the resistance. My manual said it should be 10K ohms at 78F. I was reading over 30K ohms. This is what caused the thermostat to blow, as the thermistor was telling the dryer the air temp was a good 30 degrees cooler than it actually was. You can also verify the thermostat is bad by checking it for continuity. I removed the screws on the top-back of the dryer and slid the top back to reveal the screws holding on the control panel. I removed those and popped off the control panel. It required a good bit of force. I then removed the four screws holding the front piece on and removed it by pulling it slightly towards me and up. The parts are located on the bottom right. They were underneath a black plastic flap on my dryer. I removed the cables and the took both parts out with a screwdriver. I replaced them with the new ones (they should only fit in the right slot) and reattached the cables. From there, reassemble in reverse of the disassembly.

I change the Thermistor 3 bracket and worked well for 10 minutes and the thermistor is broken again