MLE23PDFYW Maytag Dryer - Instructions

As the dryer would be going you could hear a grinding noise every other sec or so, like sandpaper sanding metal.

Disassemble as per video on this site and install replacement felt seal.

Took a bit to tear down and change and reassemble but well worth the time as there is
no one in our area that does this type of repair(s) any longer

Just follow the video. The hardest part is getting the top to disengage from the clips.

Firts I had to take all the front parts off using a screwdriver and nutdriver then I loossen the belt to get the drum out then I had to use snapping ring pliers to remove the rollers and put the new ones in I cleaned the inside of the dryer then I put everything back in place. After all that I tested it and it worked really good it took me about an hour to do all that

I made the mistake of repairing my old maytag neptune dryer with cheap eBay rollers and they crumbled apart and made a ton of noise within a month. I replaced them with quality OEM parts from partselect.com and my dryer is running like new. It's easy to do with common household tools and there are even easy to follow instructions available online.

Removed front of dryer, removed inner cover, slid roller belt off of drum to remove drum. Only tricky part was the two clip rings. My pliers had .070 tips and the ring holes were smaller so I had to run to HD to buy a pair with various size tips, ended up using the .047 tips. Only one wheel was squeaking when I rotated them by hand, but I had ordered both as recommended here so I replaced them both. Put everything back together feeling the belt to make sure it was not twisted and rolled smoothly when I rotated the drum by hand. Works great now. Lots of thanks to this site and all the posters who share their info!

replace motor as per utube supplied with parts order

If you have the option to take a part the dryer before ordering the parts to track down the squeaking part, do so. In my case a squeaking part is still usable. Unfortunately the squeaking part was not the rollers or the belt depicted as a high percentage of the squeaking problems as noted on the webpage.My was the Idler Pulley. INSTALLATION of idler pulley, I started by watching the youtube videos, took pictures during the removal of the parts to assist in the installation. removed front panels parts, moved drum forward off the rollers, reached in and pulled the idler pulley to the left in order to remove belt. pulled the drum out. And with a flat head screw driver popped off the e clip (bought extra e clip just in case i lost it) reinstalled everything, BUT take note of the Idler pulley, it has one side bigger than the other BUT in the CLOSE UP VIDEO THE GENTLEMAN INSTALLS IT BACKWARDS. Not sure if this has a major effect on the pulley, but wanted to give it a heads up (your pictures will help you with this to keep track of how it should look at the end).

Went on line and got a diagram of the dryer. Removed four screws around the door. Removed the door and then the front cover. The toughest part was removing the drum. Once I got that out of the way replacing the rollers was easy. Re installed the drum. The belt was a little tricky but worked. Then replaced the front of the dryer and the door. The dryer works fine now and no more noise. Pretty easy.

looked at video on your web site my wife and I decided to try it ourselves we are 70 and 71 And I am in a wheelchair just had surgery so we ordered parts. received parts looked at repair video a couple of times and went for it. during process we had some moments of frustration but we went back to video. end result, screech is gone. could not have done it with out video thanks.

I removed and replaced all the problem pieces, and now she runs better then when I got her!

As per video instructions we took off front and removed drum. We only changed one of the roller support wheel as I could not find any information as to how many I need for my type dryer and parts diagram was deceptive. Showed only one drum support roller.

I re-assembled, checked felts, and wear blocks,(good condition). I cleaned lint, removed coins from baffles, corrected several dents(minor), double checked wire condition and routing (good), finished re-installation, checked balance . all was good, and ran two loads of laundry. very quiet! Thanks

I've had this dryer since it was new It's over 25 years old. and it started to make a high pitch squealing sound when in use. Decided it's time to repair it. a new one is very expensive. So I ordered the parts from this site. When the parts arrived they where Inspected for fit, function and finish. So I proceeded with doing the repair myself. Short Phillips screw driver to remove the two sheet metal screws at the bottom front panel. tilted the panel from the bottom outward and removed it from the main tumbler cabinet. labeled the door switch wires one was yellow & one white. so I would not reinstall them incorrectly upon assembly. removed the front panel. set it aside. then removed the bulkhead panel 5/16" screw in each corner. removed that and set it aside. and there she was, the tumbler. I pulled the tensioner up to loosen the belt, and removed it. then grabbed the tumbler from the inside top slightly picked it upward and slid it out of the cabinet exposing the two rollers and axles one on each side that it sits on. at that point I noticed the drive belt was frayed and slightly worn. came back in the house and got on line ordered a new one from Parts Select it showed up a day later and a perfect match. the rollers are held in place by snap rings at the end of the axles. squeeze them they come off real easy, and on the back side there's a 14mm hex head nut. box wrench works good here to loosen the nut and remove the axles. the original washers are metallic and worn badly, they where making the high pitched squealing sound when they rotated so they came off and where replaced by the ones in the new roller kit and lubed with graphite not oil or grease. Graphite is dry and does not collect all the dirt and debris. put the new washers, new rollers & snap rings back on the axles grooves on the end, hand spun them and they where ready to roll. took the new belt placed it around the tumbler over the exact witness marks that where there so it would line up and lifted the tumbler back into the cabinet aligned the new belt over the motor pulley and tensioner lining it up exactly on the witness marks left by the old belt. slowly slid the tumbler back on to the new rollers rotated the tumbler a couple rotations clockwise to set the belt put the bulkhead back on the front with 5/16" sheet metal screws. in 4 corners, reinstalled the from panel along with the door switch wires and it was done. now the moment of truth. plug the machine in and turn it on!. Bingo! it runs so well you don't know it's even running. after this repair the machine performs even better. it actually takes LESS time for clothes to dry! AJS

Watched video then followed directions in the package. Installation wasn't difficult but it would have been easier if I had a set of snap ring pliers (cheep at Harbor Freight). I was surprised by the amount of lint buildup. I feel much safer now that everything is nice and clean. Clean and quiet, worth the time to make the repair.

I followed the repair videos which were very helpful and made the job easy to do. Anyone of average handyman skills should be able to perform the repair without difficulty.