MDE6800AYQ Maytag Dryer - Instructions

I was able to quickly make this repair with the help of some instructions that I found on this site on how to remove the front panel of my dryer. 4 screws on the front around the door (and removal of the door) and then it was simply a matter of rolling the top portion out to pop it out of some clips and then the front panel opened toward me and I was able to lift it off of the metal fingers that secure it on the bottom. Removing the old baffle was a matter of removing two screws with a nutdriver and installation of the new baffle was a breeze. All in all I was done start to finish in under 10 minutes.

Just took the old one out and put the new one in! Fit perfectly! Very happy with your service and part came super quick!

To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.

I removed the cover and pulled out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.

Inspect controller board and found discoloration around four resistors. Remove controller housing to access controller board. Removed four mtg. screws and wire harnesses. intalled new controller board and retest. Cycles with heat.

I looked up my problem online and everything I saw said to change the roller wheels that hold the barrel of the dryer. After doing that (twice, once on each side) I was still having a horrible squeaking sound so bad that we were waiting to do laundry until we were leaving for a while. Finally I determined that the problem was actually the idler wheel. All I had to do was remove the bolt holding the idler arm on (it's the arm that has a spring connected to it that moves to allow the belt on or off) and put the new arm with the new wheel on. The dryer is now whisper quiet and works perfectly.

The dryer started making a screeching/squealing noise…when it became unbearable, I decided to research the problem and found this website - it was tremendously helpful.

Based on what I found, I decided to order two drum rollers and two shafts – hoping that would solve the problem. My husband and I disassembled the dryer and replaced those parts. We also vacuumed the unit and wiped down the 10 years of gunk. Honestly I am surprised we have not had a fire given the amount of dust/lint inside the unit. I also took the opportunity to give the vent a good cleaning as well.

We put the unit back together, turned it on and listened to the quiet hum of our renewed dryer. Until about 15 minutes later and then the screeching/squealing started again. Kicking myself for not ordering the idler arm and shaft as well as the idler pulley wheel and bearing the first time – I went online and placed another order.

We took the unit apart a second time. We did inspect the pulley the previous time, but it appeared in good working order. Not seized like some of the other posts mentioned. Upon further inspection, it did seem to make a squealing noise when we wiggled it – duh!

The unit was put back together, quietly doing it’s job and we feel confident that we will get a few more years out of it. The videos were extremely helpful as were the posts from other do-it-yourselfers. We saved a lot of money with this fix.

Good luck!

BTW - The Lint Filter was not a problem - I just thought after 10 years, we could use a new one. I laughed when I saw the repair video on it!

Unplugged dryer. Removed dryer door with philips screwdriver. Removed front dryer panel aftr loosening philips screws on each side of door. Then at top right corners I used a nutdriver to remove clips/hooks that hold down top of dryer. I then lifted top of dryer up- it is hinged at back. I could then manually turn drum to access screws that hold baffles. I held each baffle in place with left hand and turned in screws with right hand until tight, using nut driver. I vacuumed out inside of dryer. Reassembled top, front panels and door. plugged in and tested. All good.

unplug dryer; remove dryer door; remove front cover; thermal fuse located on heater underneath and beside drum; remove two electrical leads on fuse; remove two screws holding fuse in place; install new fuse and do the above in reverse; clean lint from duct; plug dryer into

Removed Dryer Door and front face of dryer, total of 4 screws, turn dryer drum to position broken baffle screws, remove screws, install new baffle, attach front face of dryer and reattach dryer door. Time 15-30 min. total. Real easy. Thank You PartSelect. Maytag told me my part was no longer available, but I fold it at PartSelect.com.

Take old out, slide new one in. Perfect fit.

Removed four screws from the door hinges and front panel. Removed the front panel by pulling forward from the top and found two screws. The part does not come with screws which are #10 x 1 and 1/4" long hex head sheet metal screws. I believe that the screw size is critical as the part may break loose again if the screws width is too large or small for the predrilled holes in the baffle. One set of holes in the drum had slotted screw holes which would allow for installing the baffle with the screws partially installed in the baffle. I would recommend washers for that installation. Check all three baffles to ensure that all screws are tight.

I looked on line and found a scematic from your web site to determine how to dismantel the dryer. Once I was inside I was able to determine that the drum roller was making the noise. I decided to replace the other moving part while I was inside just in case. . . Pretty easy job

Removed front panel and tumbler, replaced roller axle,
wheel, and front glides. Anybody can do this.

By watching a video I disassembled the front and took the dryer tub out and replace the two rollers and it took about 60 minute.

Really easy to replace. All I had to do was remove the screws on the hinges and two on the other side. Used a nut driver to remove the brackets that hold the lid down. Secured the lid open and used the nut driver to remove the screws that hold the baffel son (two on each) and replace the baffel and secure with the screws. Reversed the the process and was drying clothes my first load of clothes in around 30 to 40 minutes. Process is really easy and I was able to do it by myself