MDE11CSACL Maytag Dryer - Instructions

took out old and placed in new

Removed back panel of machine which exposed badly worn idler pulley. Have had problem before on another dryer so I was sure what problem was before I started. Removed snap washer and cloth washer and then bad pulley.(It was very worn and wobbly).Cleaned shaft with small piece of emery paper and put two drops of oil on shaft and replaced old pulley with new one.Put back washer and snap washer.Drive belt had slipped away from its proper position so I had to remove the front panel of the dryer to place the belt back and realign it on the drum and around the new pulley and the motor drive shaft. Not really that difficult.....Machine now runs like it's brand new.....

opened the front with 2 screws, removed 4 screws to access blower, removed spring clamp and split ring, pulled off old part and replaced with new and put back together.

There were two screws to remove the front of the dryer. Then 4 screws to remove the front drum support. Remove the drum. Then one nut each on changing the back drum support rollers. Assemble the drum and front support in reverse, and door front, don't forget to put the new drive belt ovre the drum. Then from the rear panel opening, one screw to change the idler assembly. Easy

Unplug the dryer and pull it away from the wall so front and back can be accessed. Remove front panel. Remove front drum support. Remove rear access panel. Disengage drive belt from idler wheel. Make careful note of course of belt and which side is "outward". Remove drum through front. Remove Rollers using circlip pliers. Remove nuts behind shafts. Remove shafts. Clean-up area and parts before re-install.

Install new Shafts and nuts. Grease shafts. Install new Rollers, washers and clips. Drape drive belt over drum while reinstalling from front. Remount drive belt over drive and idler pullies from the rear access. During this step it helps to have a helper to position the belt around the drum in correct fore/aft position, lying flat and without twists, smooth side against drum. Install front drom support. Rotate drum to seat belt before closing up. Install rear panel cover. Install Front panel. Plug it in and turn it on for a test.

It took me a lot longer to plan the repair and decide to do it than to do the actual work, knowing what I know now, and having the parts, it would take less than half an hour. As there are no repair manuals available, it took one of these reports to give me the confidence I needed to proceed.
I first found out how to open the front (only two screews on the underneath part of the front cover) and opened it to hear the noise, (just put the cover to one side while still connected to the door switch),,,,, sprayed some WD40 all over the place and the noise went away temporarily (DO NOT DO THIS as the oil will burn off on top of heater unit and smell and smoke). I replaced the roller that the drum sits on (above the heating unit) to the right of the drum and the belt. You need a special tool that fits into the little holes in the ring retainer, I got it at Lowe's ($20 +/-). It is a Channellock plier that opens when you squeeze, you have to change the points (comes with it).
So, here is the squence: remove the front panel, disconnect the swhitch (it took some pulling), set aside; remove front drum assembly (only four screws looking at you) and it comes right out; the Drum is light and comes right out as well, it just sits in a dry channel. The belt will fall off.... take the retainer ring off the roller with the special tool... remove roller and replace with new washers (one on either side) replace the ring retainer (recommend getting new one) with same tool. If you remove the small panel in the back of the washer it is very eassy to replace the belt.... I did replace it although the old one looked almost new .. instructions and a diagram come with the parts you buy here by the way... which they should say... place belt on drum per instructions (solid side down), put belt inside the chanell on drum (it will climb to the correct position by itself) put on drum front cover to hold drum in place, and then sting belt on pulley from the back of the dryer. (diagram comes with belt otherwise look at it before taking off the drum) Replace front panel (after reconnecting switch) and you are off (if you want to test without the front panel you have to touch the switch wires to each other (use tape) and do not do plugged in...
After much anxiety but not that much work the dryer runs great and is as quiet as new.... I took the parts off before ordering by the way.... the order came within three days... I am happy to have PartSelect.com .. Maytag had not clue this model even existed.... Thanks

Overall, the repair was pretty easy. I'm a 52 year old woman who has never done drier repair. I replaced both front glides, both drum support roller wheels, the idler pulley wheel and the tumbler and motor belt. Including vacuuming out the inside of dryer and washing down the inside and outside of dryer with cleaning wipes, the whole project took me 2 hours. (if done individually, time would have been 20-30 minutes). You must have correct tools, so I did have to purchase two tools that I didn't have. My only suggestion in replacing the idler pulley wheel and the tumbler/motor belt would be to take the small access panel off the back of the dryer for easier access to the parts.

Looked in one of the back removable panels and saw the broken belt. Took the machines front panel off per a You Tube video and saw the repair was simple but too the time to vacuum out a large amount of Lint Debris that had accumulated over the past 34 years all over the inside of the machine which is dangerous.. After cleaning it all up I simply put the new belt on and put everything back together and it all works nicely again!

First I unplugged the dryer. Then, I took off the front cover, then a piece that holds the tumbler on. I put the new belt on and took a few minutes to make sure the belt was placed correctly. Lastly I put everything back on and plugged it back in. She started right up.

Tip: If the belt broke make sure the Drum Rollers are not seized which could have broken the belt. I recommend if replacing the belt replace the Drum Rollers (2- required) at the same time.
The instruction sheet that came with the Drum Roller kit is straight forward. It provided detail on what to disassemble to replace the rollers. So follow the instructions. Tip: Make sure you have a C – clip ring pliers to remove the C clip. The instruction sheet calls it the snap ring
The Idler Pulley came with no instructions, however it was easy to replace. The idler pulley is secured with an “E” shape clip which can be removed with a small straight blade screw driver.
The instruction sheet on how to install the belt was good showing how the belt is routed. The instruction wants the belt installed from the front around the tumbler then from underneath the tumbler towards the back and around the motor pulley and idler pulley. It is hard to see the motor and idler pulleys from underneath the tumbler. However I think it was easier if the tumbler was moved forward enough so you can see the motor and idler pulleys from the top. Install the belt as shown in the instruction sheet diagram around the motor pulley with the groves of the belt are against the pulley, then around the idler pulley. While holding the belt with slight tension, move the tumbler back into position while routing the belt around the tumbler and slowly turning the tumbler until the belt is completely installed. The belt should be about 1-1/2” from the back screws which hold the tumbler baffles. Note: the belt should be installed with the flat side against the tumbler. The belt should not be in the back grove of the tumbler.

Unplug dryer
Remove front (2 screws at bottom)
From bottom lift out and up to release top bracket
Move front panel gently to the left not disturbing wires
Remove blower cover with nut driver
Remove expansion clip on shaft with expansion clip pliers
Remove blower clamp with pliers
Slide blower wheel off
Replace blower wheel an reassemble

Replaced with new part from PartSelect . Works Fine.

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done

The video was excellent and made for an easy repair. Would highly recommend.

actually used the videos available on your website and it made the job really simple other than the fact that I live in Florida and it was 96 degrees and my dryer is in my non-air conditioned garage.