MDG7657BWQ Maytag Dryer - Instructions

loosened two screws on back of top,lifted top away from front panel.it just lifts off front corners,removed two screws at top corners.lift front panel up and out,this panel supports dryer tub,remove slowly,unplug door switch parts are located left side bottom two screws holding in had to have wife hold drum up to put front panel on

Ohmed coils and both had continuity so I changed radiant heat sensor. No bench test for Radiant Heat sensor. Same problem. Changed both coils and dryer works fine. Weak coils were my problem. I read thru the same issues in Parts Select forum and it said Radiant Heat sensor was problem 25% of the time. With coils having continuity and no ohm value specified for coils I made wrong choice but, I have spare parts and look for another 10 years of life in the dryer. Nice to have this forum to research appliance repair. Very helpful for parts location and installation. Dishwasher is next!

removed the timer knob from the panel(pop off the grey knob cover and the knob comes right off) remove three torx screws from the top of control panel and tilt the panel forward.Slide the timer assembly to the right(there is a lock tab you have to push down) and unplug the timer.Reverse procedure and reassemble.That was it.

Removed the door and machine front.replaced old duct assembly with new ,and reassembled front.

By following the directions included with the kit it was fairly clear. The diagrams of the control valve was helpful. It would have helped to tell which screws to remove to access the valve and where the screw was that retained the burner assembly.

I watched the video

I used a flat screw driver to pop out the old female portion and snapped in the new one. Dryer stays shut. That's it!

First changed the ignitor, which did not fix the problem. Unpug Dryer. Removed the front panel by taking out the 2 phillips screws and pulling the bottom of the panel out first, releasing the top clips. Remove the clip holding the coils on and replace them. Plugs just pull off, each are different so cn't mix them up. Both sensor and thermostat are pretty easy to get to using 1/4" drive socket. the screws can be a bit tough to get back in, but be patient. Wiring is pretty straight forward, remove from the old part and put on the new, same orientation. This is a good time to vacuum out the bottom of the dryer to get any loose lint out. Return the front panel, tilting out at the bottom to engage the top clips. Plugged it in and worked like a charm

I followed the advice posted by other customers. I took the front off the dryer, put the door back in place and ran a cycle. I could see that the igniter was heating properly, but no gas was flowing. Based on what I read I concluded that it was a problem with one of the gas valve coils. It was relatively inexpensive to replace both (and the dry is 10 years old), so I didn't go to the trouble of determining the bad one. I replaced them both. Obviously I unplugged the dryer (no need to turn off gas). There were 2 screws that held the bracket in place which holds the coils. I disconnected the coils, removed the bracket screws, replaced the coils, reattached the bracket screws and reconnected the coils. I then reattached the front plate to the dryer. It was very easy and took about 20 minutes and I had never worked on a dryer before.

Removed four philips screws, two holding door on and two on opposite side of door in order to remove front cover. Then removed two 5/16 screws holding clips that lock the top cover down. Then the top cover hinges up with open access to the drum. The baffles are held into place with two #10 x 1 1/4" screws with 5/16" head each. These had pulled through the drum. Installed new baffles (do NOT come with screws / you'll have to buy some). Had to put small washers (also had to buy) on the screws to hold it onto the drum since the other screw heads pulled through the drum. Closed lid, installed retaining clips, installed door onto frame, installed front cover around door, then screwed door hinges into front cover and screws to other side. Took about as long to write these directions as it did to actually do the work... EASY job!!

Removed and replaced both the thermostat sensor and the ignitor. Tested thej dryer and it worked. Replaced the front panel and it was good to go.

removed dryer door 4 screws
removed front panel
removed front tumbler bracket
removed blower cover
removed wires attached to heat and door sensors
removed top
removed drum and belt
removed side panel
removed clamp holding idler pulley
replaced pulley and clamp
reversed above steps

Using the pictoral parts diagrams on the PartSelect website, it was a logical process to disassemble the dryer to change the drum drive belt. This was a great opportunity to clean lint from the motor and air passages and inspect all components. Cleaned the belt track, the roller drum wheels and felt seals. Unit now runs like new. BTW - very fast shipping on the replacement belt and it was the right part the first time!

Followed your video; replaced felt seal on front of drum, (torn in two or three places), and replaced both front guide kits,which were ground to the metal, causing the black dust, ( metal shavings). Thanks for the help, Buck. The drum support rollers were OK.

I just needed to replace a knob because the original, (plastic) broke. What was great was how soon I received my order, just a matter of a couple of days. I wish I had ordered several as both my washer and dryer have the same ones (five in total) and now another one as broken! I think I will order three or four move.