MDE16PRAGW Maytag Dryer - Instructions

I looked at this website and found the symptoms, noisy, and no heat or not enough heat. I ordered the recommended parts. They were the drum support roller kit, idler pulley wheel and bearing, high limit thermostat, and lastly the front glide kit. I had anticipated having to use all of these parts. Upon following the instructions in the videos (couldn't ask for better instructions) I disassembled the dryer to see how bad everything was before replacing the parts. The left drum support roller spun easily, but had a little roughness and slight noise, the right one spun easily but not like I thought a new one would have spun, the idler pulley was stiff and very noisy. The thermostats all seemed to be in good shape (had continuity). I cleaned the bearings and shafts of all of the rollers with alcohol, paper towels and cotton swabs. The bearings and shafts all looked like new, so I lubed them with a slight amount of high temperature grease and reassembled the rollers. They moved smoothly and quietly. The fan was quite full of lint, even cleaning the filter after every load does not stop all of the lint. It has been in use probably over 10 years. After everything was back together, it runs like a well oiled sewing machine and has been drying well. I did return the parts unopened. This would not have been so successful without the videos. Thanks to all of you.

Replaced damaged parts and recommended parts normally causing the problem. Dryer is working again like new. I expended $112 rather than $600 for a new equipment. Good deal!

Per instructions I printed off online: took off door, then the front panel. Pulled out the old switch/button, connected the new switch/button, made sure the new button was working; put the panel back on then the door and DONE!

I had replaced belt, but the noise continued. Ordered new rollers and washer. Removed the front panel by tipping the dryer back against the wall and removing two screws at the bottom of the panel. Tipping the dryer makes it easy to remove the front panel. Removed the front drum support by removing four (4) screws. I was then able to just move the drum enough to have access to the rollers. Didn't even have to remove the belt. Replaced the rollers. Needed special pliers to remove and replace the retaining rings. Put the drum back into position and mounted the front drum support. Tightened four screws and then put the front panel back on. Plugged it in and tested it. Problem solved. Took about 35 minutes. Thanks

i removed the 2 screws holding the door hindges on. then i removed the 2 adjasent screws to remove the front door panel. i rotated the drum to aceses the screws holding the baffle and installed the baffle .

Piece of cake. Use the available manual to ascertain dismantling procedure. Only thing that might be tough for average DIY'er is the internal snap rings. Snap ring pliers are mandatory for quick easy repair.
Total time was probably about 15 minutes and this was the first time I had taken it apart. Quiet as a mouse now!
Very helpful site.

I was able to quickly make this repair with the help of some instructions that I found on this site on how to remove the front panel of my dryer. 4 screws on the front around the door (and removal of the door) and then it was simply a matter of rolling the top portion out to pop it out of some clips and then the front panel opened toward me and I was able to lift it off of the metal fingers that secure it on the bottom. Removing the old baffle was a matter of removing two screws with a nutdriver and installation of the new baffle was a breeze. All in all I was done start to finish in under 10 minutes.

Took off front. Removed door. Removed drum support. Removed drum and belt. Made sure motor was correct size and fit. Removed blower wheel. Disconnected wire plug from motor and slid motor out of blower wheel. Replaced everything in reverse order. Figuring out belt tensioning position was a trip, but finally got it. Vacuumed out all the lint. Amazingly it worked!

I looked up my problem online and everything I saw said to change the roller wheels that hold the barrel of the dryer. After doing that (twice, once on each side) I was still having a horrible squeaking sound so bad that we were waiting to do laundry until we were leaving for a while. Finally I determined that the problem was actually the idler wheel. All I had to do was remove the bolt holding the idler arm on (it's the arm that has a spring connected to it that moves to allow the belt on or off) and put the new arm with the new wheel on. The dryer is now whisper quiet and works perfectly.

Replaced both rollers,shafts, bearings and snap rings.

Removed Dryer Door and front face of dryer, total of 4 screws, turn dryer drum to position broken baffle screws, remove screws, install new baffle, attach front face of dryer and reattach dryer door. Time 15-30 min. total. Real easy. Thank You PartSelect. Maytag told me my part was no longer available, but I fold it at PartSelect.com.

unplug dryer; remove dryer door; remove front cover; thermal fuse located on heater underneath and beside drum; remove two electrical leads on fuse; remove two screws holding fuse in place; install new fuse and do the above in reverse; clean lint from duct; plug dryer into

Followed instruction video

Removed four screws from the door hinges and front panel. Removed the front panel by pulling forward from the top and found two screws. The part does not come with screws which are #10 x 1 and 1/4" long hex head sheet metal screws. I believe that the screw size is critical as the part may break loose again if the screws width is too large or small for the predrilled holes in the baffle. One set of holes in the drum had slotted screw holes which would allow for installing the baffle with the screws partially installed in the baffle. I would recommend washers for that installation. Check all three baffles to ensure that all screws are tight.

my son did the installation according to your excellent video instructions