MLE23PDAGW Maytag Dryer - Instructions

i took off the door and the front of the drum and removed the drum. I removed the locking clip from idler pully and replaced and lubricated the shaft and slid the new idler pully on. I hung the belt over the back and put the drum back in and aligned the belt and turned by hand to get the belt in the correct position. Belt came off a couple of times because i think the belt was twisted. installed the front panel and the door, plugged the cord in and started it up and it was perfect.

Followed the video. Hardest part was getting the belt around the ideler pulley and motor pulley without seeing. But I got it! Thanks to this site you rock!

I made the mistake of repairing my old maytag neptune dryer with cheap eBay rollers and they crumbled apart and made a ton of noise within a month. I replaced them with quality OEM parts from partselect.com and my dryer is running like new. It's easy to do with common household tools and there are even easy to follow instructions available online.

Removed front of dryer, removed inner cover, slid roller belt off of drum to remove drum. Only tricky part was the two clip rings. My pliers had .070 tips and the ring holes were smaller so I had to run to HD to buy a pair with various size tips, ended up using the .047 tips. Only one wheel was squeaking when I rotated them by hand, but I had ordered both as recommended here so I replaced them both. Put everything back together feeling the belt to make sure it was not twisted and rolled smoothly when I rotated the drum by hand. Works great now. Lots of thanks to this site and all the posters who share their info!

I watched a video on YouTube for the disassembly of the dryer. The parts replacement took less than 20 minutes; the rest of the time was spent on disassembly and reassembly.

Replaced the heating element and both thermostats. Hope that takes care of problem! You tube was a tremendous help through video's.h

I followed the video instructions which were excellent. Dryer repair was a cinch.

Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.

The video from this site is perfect. Unplug dryer, remove front panel, unclip wires, remove next panel and pull the drum out. Replace drum support wheels using snap ring pliers (buy the pliers with changeable tips because the holes in the snap ring were pretty small on mine). Put it all back together. The trickiest part is getting the belt back on...just be sure it's not in the groove around the drum and pay attention to how to get it on the motor wheels. Good luck!

If you have the option to take a part the dryer before ordering the parts to track down the squeaking part, do so. In my case a squeaking part is still usable. Unfortunately the squeaking part was not the rollers or the belt depicted as a high percentage of the squeaking problems as noted on the webpage.My was the Idler Pulley. INSTALLATION of idler pulley, I started by watching the youtube videos, took pictures during the removal of the parts to assist in the installation. removed front panels parts, moved drum forward off the rollers, reached in and pulled the idler pulley to the left in order to remove belt. pulled the drum out. And with a flat head screw driver popped off the e clip (bought extra e clip just in case i lost it) reinstalled everything, BUT take note of the Idler pulley, it has one side bigger than the other BUT in the CLOSE UP VIDEO THE GENTLEMAN INSTALLS IT BACKWARDS. Not sure if this has a major effect on the pulley, but wanted to give it a heads up (your pictures will help you with this to keep track of how it should look at the end).

Firts I had to take all the front parts off using a screwdriver and nutdriver then I loossen the belt to get the drum out then I had to use snapping ring pliers to remove the rollers and put the new ones in I cleaned the inside of the dryer then I put everything back in place. After all that I tested it and it worked really good it took me about an hour to do all that

As the dryer would be going you could hear a grinding noise every other sec or so, like sandpaper sanding metal.

Disassemble as per video on this site and install replacement felt seal.

Took a bit to tear down and change and reassemble but well worth the time as there is
no one in our area that does this type of repair(s) any longer

Went on line and got a diagram of the dryer. Removed four screws around the door. Removed the door and then the front cover. The toughest part was removing the drum. Once I got that out of the way replacing the rollers was easy. Re installed the drum. The belt was a little tricky but worked. Then replaced the front of the dryer and the door. The dryer works fine now and no more noise. Pretty easy.

I took the front door off, then i took the the front facing off so i could see in where the idler pulley was. Then I took a couple of screws out so i could get the tumbler out so i could put the belt back on track. I replaced the pulley and then started putting everything back together and now the dryer works like a brand new one. I loved buying parts from here. Cause you are showed how to replace the parts you are wanting to replace. I was very satisfied with everything.

I unscrewed the door catch and pried out with some resistance the strike part. Screwed in the catch and pushed in the strike. Closed door. Voila!! Back in business with assurance.