DG23CD Maytag Dryer - Instructions

The difficult part was to find what component was bad. Maytag does not sell the manual for this machine any more. We could not figure out what the problem was until we decided to check the voltage on the board and compare it to a second machine that we have. The second machine showed different readings so we decided to compare voltages on the transformer (main) that is at the bottom of the machine. There is a Primary (110 volts) and two secondaries; one which output is about 26 VAC and the other is above 10 VAC. The bad transformer had no output in one of the secondaries. Replacing the transformer was pretty simple. Make sure to disconnect the machine please before doing the repair.

Old latch and door striker were pried out with a flat blade screwdriver. New components popped right in. Repair was less than two minutes.

Remove back panel n u can see the sensor and easy to replace thanks to the print out i was provided love this website

I had an issue where I was not getting any power to my ignitor. After replacing the ignitor with a fresh one, the problem persisted. Next, I went hunting all the fuses and therrmostats for continuity. All seemed fine. So finally I decided to jump the flame sensor which is located on the outside of the flame tube. WHALLA! It ignited the glow plug. So with one 1/4"" nut driver I removed the single bolt from the unit, then I used a pliers to remove the two wires from the old unit. I replaced the sensor with Tue new unit and all was well. It took less than 5 min once I diagnosed the problem.

My dryer stopped producing heat and everything else was working fine. I did some research on this site and others had the similar problem pointing to the ignitor going bad. I needed to determine which ignitor fit my dryer. What I learned is that some of the parts come with a series number and you need to know which one matches your serial number. My serial number started with 40 and I had a choice of buying the part for a series 10 or 60 series. In my case I needed to buy the 10 series since you either go with the same number as your serial number or lower, never higher. When the part came in I removed the dryer door by removing the 2 screws. I then removed the 2 screws on the opposite side of the door. Once the 4 screws were removed I was able to take the front cover off. The ignitor was on the right side and easy to get to. I unplugged the ignitor and used my socket set to remove the bolt. Once removed I vacuumed the lint in the dryer and installed the new ignitor carefully not touching the black area of the part. I put the front cover back on, put the door in place and put all 4 screws back in place. I started the dryer and it was fixed! This was an easy job to repair that saved me money.

Removed front cover, removed housing cover, took old fan off, installed new fan, put covers back on.
Your instructional video was very helpful. He told which screws to remove to get the covers off. I was unsure about how access the fan until I watched. Well done!

Followed advice from here; unplugged machine from power source, removed two phillips head screws located just out of sight below the little indentaion on the front panel, removed front panel & set aside the machine. Unclipping the door switch wires allowed for enough slack so that they didn't need to be disconnected. Unscrewed (or un-hooked, don't remember) the lint box, pulled the drum out slightly, removed the belt, pulled drum out all the way & set aside. Removed the snap rings & wahsers from the idler wheels, removed wheels, put a light coating ot synthetic grease on the shafts & in the idler bushings, re-installed idlers, washers, & snap rings. Re-assembled in reverse order of assembly with alittle difficulty iin getting the new belt in the proper configuration. Removed small access panel in rear of machine to assist in installng the belt finally realizing that the belt DOES NOT go in the indented area of the drum, but on the larger diameter of the drum itself. Tested by rotating by hand, re-assembled front cover, plugged it in & dried the laundry......QUIETLY!

Shut off or unplugged dryer for safety.

Slipped thin blade putty knife up under bezel of switch to unlatch from the panel and pulled forward to remove the swwitch from the dryer. Unplugged the quick connect terminals (3) from the old switch and plugged them onto the new switch. one of the terminals had gotten quite hot and darkened the insulation so it was replaced with one that was supplied with the switch. that was a cut, strip, crimp process. Placed the new switch into the panel and snapped into place.

remove bottom section under door 2 screws remove door 2 screws remove switch by squeezing tabs install 2 new female ends on wires supplied with switch . put switch back in plug in wires .

I had to remove the drum. 1. remove lower panel. 2.remove the vent duct. 3.Remove the door (be sure to mark the door switch electrical wire with tape NO, NC, COM). the switch is marked. 4 Slacken the drive belt by removing from its idler pulley. 5.Pull the drum forward & out, by lifting the top without removing it (may have to struggle a bit by bending the sides of the dryer outward). 6.Large 3/4" socket remove the squrrel cage fan counter clock-wise. 7.Unplug the wire harness to the motor and with a large flat bladded screw driver push the spring clamps down & out-ward to remove them.
I always take pictures with my digital camera before removing a part so when I reinstall the part if a question of position or what went were I have it documented in my camera to view.
I install the belt and use scotch tape to hold it in place before I reinstall the drum.
The best part was being able to access the interior of the dryer to clean the lint out.
I hope this helps!

Thank you very much for your prompt service. This was so cool... On Monday night my wife told me the dryer was not heating. I did a basic diagnosis, checked the internet for parts and lowest price and found your site. I ordered the part I thought I may need and 2 days later the part arrived and the dryer is working again.

Way to go, PartSelect!

Dryer stopped heating after a few days of it being an intermintant problem. I ohmed the heating coil and it was fine @ 12-15 ohms and the 2 sensors were open so I knew they were not the problem. The only item left was the Heater Relay. As soon as it was changed, dryer operated as it should.

Sensor is in the front lower left. Gas off, electicity off. Removed two screws for the filter, pry/lifted the top up and taped it too the overhead cabinet, removed two screws inside top of front panel, lifted pandel with door closed staight off. Two screws to remove the flame sensor braket. unplug the old sensor install the new one and reverse everything. With others suggestions I purchased temperature switches etc. but the radiant flame sensor was the problem. I now have some spare switches for future. Excellent company and very quick service. Oh, Sears wanted 200.00 just for the service call, I live rural.

I observed that the top of the dryer was affixed by two screws at each front corner. With these removed the top of the dryer could be easily lifted and with the front support panel removed the drum, drive motor and idler pulley could be accessed. This allowed the installation of a new drum belt in a short period of time. Installing the belt from the front lower left hand side proved very difficult for me but with the top raised and coming in from the top it was accomplished in short order. Thank you, Wesley Harmon

Press in the new female latch part with thumbs. Took about two seconds!