DG107 Maytag Dryer - Instructions

Shut off or unplugged dryer for safety.

Slipped thin blade putty knife up under bezel of switch to unlatch from the panel and pulled forward to remove the swwitch from the dryer. Unplugged the quick connect terminals (3) from the old switch and plugged them onto the new switch. one of the terminals had gotten quite hot and darkened the insulation so it was replaced with one that was supplied with the switch. that was a cut, strip, crimp process. Placed the new switch into the panel and snapped into place.

Removed front cover, removed housing cover, took old fan off, installed new fan, put covers back on.
Your instructional video was very helpful. He told which screws to remove to get the covers off. I was unsure about how access the fan until I watched. Well done!

remove bottom section under door 2 screws remove door 2 screws remove switch by squeezing tabs install 2 new female ends on wires supplied with switch . put switch back in plug in wires .

Removed the back of the control panel. Made note of wiring and disconnected same. Pried off center of dial with screwdriver. Removed circlip with needle nose pliers and removed dial. Removed two screws with nut driver and removed timer. Installed new in reverse order.

I had to remove the drum. 1. remove lower panel. 2.remove the vent duct. 3.Remove the door (be sure to mark the door switch electrical wire with tape NO, NC, COM). the switch is marked. 4 Slacken the drive belt by removing from its idler pulley. 5.Pull the drum forward & out, by lifting the top without removing it (may have to struggle a bit by bending the sides of the dryer outward). 6.Large 3/4" socket remove the squrrel cage fan counter clock-wise. 7.Unplug the wire harness to the motor and with a large flat bladded screw driver push the spring clamps down & out-ward to remove them.
I always take pictures with my digital camera before removing a part so when I reinstall the part if a question of position or what went were I have it documented in my camera to view.
I install the belt and use scotch tape to hold it in place before I reinstall the drum.
The best part was being able to access the interior of the dryer to clean the lint out.
I hope this helps!

Thank you very much for your prompt service. This was so cool... On Monday night my wife told me the dryer was not heating. I did a basic diagnosis, checked the internet for parts and lowest price and found your site. I ordered the part I thought I may need and 2 days later the part arrived and the dryer is working again.

Way to go, PartSelect!

Sensor is in the front lower left. Gas off, electicity off. Removed two screws for the filter, pry/lifted the top up and taped it too the overhead cabinet, removed two screws inside top of front panel, lifted pandel with door closed staight off. Two screws to remove the flame sensor braket. unplug the old sensor install the new one and reverse everything. With others suggestions I purchased temperature switches etc. but the radiant flame sensor was the problem. I now have some spare switches for future. Excellent company and very quick service. Oh, Sears wanted 200.00 just for the service call, I live rural.

Turned out to be the primary coil on the gas valve. If you remove the cover of the coils and wait for the dryer to try to start the flame the coils are energized, a magnet is turned on. By lifting the coil you should feel the magnet if the flame is on. If the flame does not come on after the ignitor fires check to see if the coils are energized. If not buy the set, it's cheaper then purchasing them separately.

I observed that the top of the dryer was affixed by two screws at each front corner. With these removed the top of the dryer could be easily lifted and with the front support panel removed the drum, drive motor and idler pulley could be accessed. This allowed the installation of a new drum belt in a short period of time. Installing the belt from the front lower left hand side proved very difficult for me but with the top raised and coming in from the top it was accomplished in short order. Thank you, Wesley Harmon

Press in the new female latch part with thumbs. Took about two seconds!

I used a flat screw driver to pop out the old female portion and snapped in the new one. Dryer stays shut. That's it!

I pulled the face of the dry off by removing the two screws on the lower face below the door. I pulled the drum out by removing the two bolts holding the drum mounts to the frame. I put the new belt around the drum and remounted it. The access hole on the lower right corner on the back of the appliance allowed me to turn the drum to align the belt (and turn it right side up) with the pulley. It took a moment to figure out how to re-thread the pulley but was able to do it after only a couple of tries. All in all it was quite easy!

By following the directions included with the kit it was fairly clear. The diagrams of the control valve was helpful. It would have helped to tell which screws to remove to access the valve and where the screw was that retained the burner assembly.

I watched the video

Removed two screws and lifted the control console then tilted forward the shell. Removed two screws holding the latch cover and assembly then disconnected two wires. I played with the assembly until I discoved the element was toast. Ordered the part but when I got it I was confused because it had three prongs (two on one side and one on the other) when the burnt one had only one and one and I only had 2 disconnect wires. I thought I had gotten the wrong part but figured it out. Actually putting the assembly together was the easy part, trying to get the outer shell back together was a little tough. Between taking it a part, figuring out what was wrong and ordering and receiving the part was about three weeks. So when putting it all together took awhile but I did it and it works great.