MDE16CSAYW Maytag Dryer - Instructions

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

I took out the old worn out part and replaced with the one I order.

Unscrewed door and front panel. Pulled and took the, off. Used standing flashlight to illuminate the area underneath the dryer barrel. Tried various tools to take out broken plastic remnants. Then, used small electric nutdriver to screw the tall baffle into place with newly purchased metal screws. Was a bit hard to reach and tight but finally worked once I found an appropriate tool and top.

After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!

First removed front door 2 screws holding it to frame, then removed 2 screws holding front cover panel on tilt out front panel, used vac to clean inside, removed idler arm with pully attached, replaced with new parts when I did a test run still had a llitle squeek, the drum support wheel on right looking from front making some squeeking,I went back in removed part shaft had small rust spot cleaned with jewelers cloth lubed and wiped off, no more squeek I wish I had ordered new drum wheel when I ordered idler parts, then I could have done a complete overhaul now I know more I have never worked on a dryer before the drawings on the web site heleped a lot

I removed the dryer door and attaching hardware to other covers. Raise the top cover and prop it up. Remove the drum retaining cover and disconnect the door switch wires, making note of their locations. Release tension on idler and take belt off of motor. Pull the drum out with belt still around it. Vacuum lint and dust from inside cabinet. Use snapring pliers and remove the snaprings on the drum rollers. Remove the old rollers and washers, clean the shafts and apply a light film of oil on the shafts. Install new rollers and plastic washers on shafts and secure with snaprings. Remove the "E" clip from the idler shaft and remove the old roller. Clean and lube the shaft and install the new idler and clip. Place the new belt on the drum with the ribs against the drum. Put the drum in place and install the front drum retainer. Position the belt around the motor pully and tensioner. Rotate the drum to get the belt to track. Attach the remaining covers.

We could not find directions for the brand that we have. First we took the back off, which we did not need to do.
lift the top of the dryer, remove the front remove drum. Place belt on front of motor, wrap double belt around support on bottom of dryer, open the remaining belt and stretch around drum. Hold drum in place, replace front and top.
Need at least 2 people, not at all intuitive.

Others have described how to remove 4 screws and remove the front panel of the dryer. The problem I saw is that some screws broke off and fell inside while others remained on the separated baffle. The old screws that I found were 1 1/4 inch. The parts manual indicates a replacement screw that is 1 inch long and a number 10 width. One set of holes for the baffles has slotted holes. It appears that wear in the paint indicates movement before breaking off. My solution to the slotted holes was to use washers on the screws and to tighten the screws in the position where any force was not going to move the screws to the center position of the slots. The force of the separation caused the slotted holes to expand.

The video was excellent and made for an easy repair. Would highly recommend.

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done

We inherited this dryer three years ago upon purchasing our current house. At that time I found this website to purchase and install a couple of the baffles that were missing. This time, I checked the troubleshooting for my current problem and ordered all of the parts I felt I needed to resolve the problem. Once I received the parts, I followed the great how-to videos by Steve to disassemble the front of the dryer and remove the drum. I could not get to the repairs right away since the interior of the dryer was quite dirty and I took a lot of time to clean it out. Once I got to removing and replacing the drum rollers, idler pulley, rear drum felt shaft, and drum belt, everything went smoothly and was just as easy as Steve described in the videos. If I didn't have such a dirty machine interior, removing the old parts and installing the new parts would have taken less than an hour. I had to hold off on installing the front glide kit and front drum felt seal since I forgot to order two of each (I'll install these at a later date. I proceeded to putting everything back together and testing the dryer. The dryer now runs quietly and works great.

replaced

Went on line and got a diagram of the dryer. Removed four screws around the door. Removed the door and then the front cover. The toughest part was removing the drum. Once I got that out of the way replacing the rollers was easy. Re installed the drum. The belt was a little tricky but worked. Then replaced the front of the dryer and the door. The dryer works fine now and no more noise. Pretty easy.

If you have the option to take a part the dryer before ordering the parts to track down the squeaking part, do so. In my case a squeaking part is still usable. Unfortunately the squeaking part was not the rollers or the belt depicted as a high percentage of the squeaking problems as noted on the webpage.My was the Idler Pulley. INSTALLATION of idler pulley, I started by watching the youtube videos, took pictures during the removal of the parts to assist in the installation. removed front panels parts, moved drum forward off the rollers, reached in and pulled the idler pulley to the left in order to remove belt. pulled the drum out. And with a flat head screw driver popped off the e clip (bought extra e clip just in case i lost it) reinstalled everything, BUT take note of the Idler pulley, it has one side bigger than the other BUT in the CLOSE UP VIDEO THE GENTLEMAN INSTALLS IT BACKWARDS. Not sure if this has a major effect on the pulley, but wanted to give it a heads up (your pictures will help you with this to keep track of how it should look at the end).

i took off the door and the front of the drum and removed the drum. I removed the locking clip from idler pully and replaced and lubricated the shaft and slid the new idler pully on. I hung the belt over the back and put the drum back in and aligned the belt and turned by hand to get the belt in the correct position. Belt came off a couple of times because i think the belt was twisted. installed the front panel and the door, plugged the cord in and started it up and it was perfect.