MDE12CSAGW Maytag Dryer - Instructions

Looked in one of the back removable panels and saw the broken belt. Took the machines front panel off per a You Tube video and saw the repair was simple but too the time to vacuum out a large amount of Lint Debris that had accumulated over the past 34 years all over the inside of the machine which is dangerous.. After cleaning it all up I simply put the new belt on and put everything back together and it all works nicely again!

The video was excellent and made for an easy repair. Would highly recommend.

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done

Replaced with new part from PartSelect . Works Fine.

Remove the two screws that hold the front cover. Remove front cover and disconneted wiring to door switch.Remove the cover ( lower right hand corner )back of the dryer to gain access to belt idler pulley/tensioner. Remove old belt and slide new belt on the tumbler.

After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!

Remove the door and the plastic brackets on the other side of the door opening. Remove the front cover by gentally pulling from the top first. Support the dryer basket (I used an old towel and a block of wood. With a 1/2 inch wrench remove the Roller Shaft with the Drum Support still attached. Replace new shaft and drum support. (always replace both at the same time or you will find that the problem will come back much sooner.) Careful when installing. Make sure that the new non metalic washers (suppied) are propery seated when you are tightening down the nut.

First I unplugged the dryer. Then, I took off the front cover, then a piece that holds the tumbler on. I put the new belt on and took a few minutes to make sure the belt was placed correctly. Lastly I put everything back on and plugged it back in. She started right up.

I happened to come across a repair story posted by Wayne From Minneapolis MN about how he reinstalled the tumbler, plugged the dryer in, and started it up but forgot the belt and realized that it was the blower wheel that was loose on the shaft. As soon as I read that, I said, "Yes! that's it!" So I ordered the blower wheel and a belt. I decided to replace the belt since I saw it was slightly frayed. After all, the dryer is almost 20 years old!

First, switched off the power to the dryer or disconnect it from the outlet. Took the front panel off by removing the two screws near the bottom of the dryer. Pulled the bottom of the panel out and the two clips on the top just disengaged easily. Be careful, there are two wires connected to this panel. Just rotated it to the left and let it rest vertically. If need be, the two wires can be removed easily.

Next, I removed the four screws to take out the front tumbler and the tumbler. Set them aside. Then I removed the belt. You might want to pay attention as to how the belt goes around the motor pulley and the idler pulley before removing the belt.

After nearly 20 years, I'm surprised that it wasn't full of lint and dust. Gave it a good vacuuming and clean up.

Next, I removed the blower cover, the retaining ring, the hub clip, and the blower wheel. Installed the new blower wheel, hub clip, and here's the challenging task without the proper tool - putting the retaining ring back on the shaft! It took me about 5 minutes to put it back on the shaft with a small flat-head screw driver and an awl. Reinstalled the blower cover.

Next, I put the new belt over the pulleys and loosely hung the belt on the back tumbler to hold it up. Then I put the tumbler back in and worked the belt over the tumbler. I let the belt sat in the groove of the tumbler first and then when the tumbler was in position, I worked the belt over the two pulleys in to the proper position. Then I moved the belt to strap over the top of the tumbler. At this point, I just rolled the tumbler with my hand when part of the belt was out of the groove and on top of the tumbler. The motion took care of getting the rest of the belt out of the groove and on top of the tumbler as it should be located. Reinstalled the front tumbler and then the front panel.

Powered it back up and started the dryer and viola! the rumbling noise was not to be heard. Just like it used to sound - a low humming noise. Thanks Partselect.com for the helpful repair stories and the speed in getting the parts to me.

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

I took out the old worn out part and replaced with the one I order.

Problem was the blower wheel, (Plastic deteriorated). Replaced the tumbler and motor belt as well as th idler pulley. While the blower wheel turned out to be the problem, the other parts were significantly deteriorated. Since I had the dryer disassembled it made sense to replace the other parts. The 24 year old dryer runs like new. The parts select instructional videos were extremely helpful.

I bought this machine in 1984. For the belt to last this long, is extraordinary. The belt comes in a plastic bag with instructions. After removing the front cover(2 screws at the bottom, tip bottom out towards you. Cover unhinges from the top. Lean face against a wall. Don't remove any wires). I then vacuumed the inside thoroughly. Used a parts brush to wipe everything off, and blew out with compressed air. Vacuumed again. A bit obsessive, but gas and dust are not a good combination. So why not take the extra time. There is a continuous mark on the circumference of the drum, left by the original belt. Use this as your guide to locate the new belt. Rotate the drum by hand to make sure it tracks correctly. I also ran the motor with everything open, to make sure everything was cool before I buttoned it up. Also took the time to replace the gas line with a new one, and duct-taped the vent pipe to improve air flow.

replaced

This dryer has been really reliable. This is the first time I've had to repair it. PartsSelect.com says the noise had a 30% chance the problem would be the tumbler rollers and shaft and 18% it would be the blower impeller fan. I took a chance on the rollers, thinking I would save $20 on the blower fan. Big mistake! Once I dissambled the dryer, I realized almost immediately it was the blower fan and not the rollers. When I manually turned the motor shaft, I discovered the problem. The plastic fan's shaft hole is worn to a larger diameter and is semi-freewheeling on the shaft causing the racket. I replaced the rollers and belt and ordered a new fan. I tried putting electrical tape on the shaft to enlarged the OD like a fellow on this site said, but it worked for about 3 minutes then the racket started again. Also, I had to pull the dryer away from the wall and open the access door to the back of the motor in order to thread the drive belt on the motor and idler pulleys. I couldn't fit my arms along side and under the tumbler. I've got the scratches on my left arm to prove it. Suggestion: Replace the blower fan, rollers and shafts if you have the rumbling noise when operating the dryer. Might as well replace the drive belt while you have it apart, too.