MDG12PSAGW Maytag Dryer - Instructions

opened the front with 2 screws, removed 4 screws to access blower, removed spring clamp and split ring, pulled off old part and replaced with new and put back together.

I watched your YouTube video. Access to the interior of the dryer and replacing parts was EASY. Unlike the machines in the videos ACCESS is VERY EASY as only one panel needs to be removed. Access is from the FRONT PANEL and secured by two top clips and two front bottom screws. Just unscrew and swing the bottom up at about a 45 degree angle; the panel comes off and can be placed to the side. I first replaced a thermostat and a coil kit but still no heat. I then ordered a new FLAT STYLE IGNITER ( which I discovered was broken off ) and a RADIANT FLAME SENSOR and these parts FIXED THE PROBLEM. Parts cost about $90 (Dec. 2016) including shipping.

I followed the videos provided, the only think I would added is cleaning the riding surface of the drum. In my case the drum had gunk on it from the old pads, witch got on the new pads causing it to continued to make noise.

It would be wise to also get the felt and belt, to replace them all the first time.

Removed front cover.removed 4 screws holding drum in place. Cleaned out lint from everywhere. Placed new belt over drum looping it over idler arm & motor pulley. Pushed drum back ; rotated drum to see that belt was engaged. Put front drum bracket in place. Put front panel in place with 2 screws at the bottom. Tested motor & rotation of drum; then checked heat. All worked fine. Took 1 hr. but most time spent cleaning lint.

I removed the front of the dryer and the drum support plate. I drilled out the old rivets and installed the Glides with the enclose rivets. The Glides came loose in a few days! The holes in the glides are larger than in the old Glides. I disassembled the dryer again and reassembled with my rivets. This time I held the rivet gun inside the perimeter of the dryer so that the head of the rivet is opposite the initial installation. So far, so good, except the dryer still squeaks. The idler pulley is now the culprit. White grease burned up. I reassembled with high temperature grease. If that does not work, I will need another idler pulley. The journal looks very worn. the dryer is 30+ years old.

We had trouble getting the front of the dryer off; we tried to pry the top off. It works better if you remove the screws at the bottom of the front panel ;) Once we had the front off, we used a 1/4" ratchet wrench to take the front off the fan housing. We took off the compression clamp off easily with a pair of priers. Removing the retainer clip was harder; we ddn't have the right tool. We removed the broken fan. We ordered the part, easy peasy, from this website. Had to buy a $9 tool to put the retainer washer back on. We reassembled the fan housing and put the fron back on. It worked! Total cost: ~$30.00. Actual time (excluding waiting for parts and buying tools): 2 hours.

Unplug the dryer and pull it away from the wall so front and back can be accessed. Remove front panel. Remove front drum support. Remove rear access panel. Disengage drive belt from idler wheel. Make careful note of course of belt and which side is "outward". Remove drum through front. Remove Rollers using circlip pliers. Remove nuts behind shafts. Remove shafts. Clean-up area and parts before re-install.

Install new Shafts and nuts. Grease shafts. Install new Rollers, washers and clips. Drape drive belt over drum while reinstalling from front. Remount drive belt over drive and idler pullies from the rear access. During this step it helps to have a helper to position the belt around the drum in correct fore/aft position, lying flat and without twists, smooth side against drum. Install front drom support. Rotate drum to seat belt before closing up. Install rear panel cover. Install Front panel. Plug it in and turn it on for a test.

There were two screws to remove the front of the dryer. Then 4 screws to remove the front drum support. Remove the drum. Then one nut each on changing the back drum support rollers. Assemble the drum and front support in reverse, and door front, don't forget to put the new drive belt ovre the drum. Then from the rear panel opening, one screw to change the idler assembly. Easy

Overall, the repair was pretty easy. I'm a 52 year old woman who has never done drier repair. I replaced both front glides, both drum support roller wheels, the idler pulley wheel and the tumbler and motor belt. Including vacuuming out the inside of dryer and washing down the inside and outside of dryer with cleaning wipes, the whole project took me 2 hours. (if done individually, time would have been 20-30 minutes). You must have correct tools, so I did have to purchase two tools that I didn't have. My only suggestion in replacing the idler pulley wheel and the tumbler/motor belt would be to take the small access panel off the back of the dryer for easier access to the parts.

Looked in one of the back removable panels and saw the broken belt. Took the machines front panel off per a You Tube video and saw the repair was simple but too the time to vacuum out a large amount of Lint Debris that had accumulated over the past 34 years all over the inside of the machine which is dangerous.. After cleaning it all up I simply put the new belt on and put everything back together and it all works nicely again!

The numbers on the metal plates were the JC Penney numbers - that no one recognizes. I eventually found the model number inside the timer case on a printed schematic. I started by disassembling whatever metal covers were removable by finding sheet metal screws and unscrewing them. If you pull on the sheet metal covers, you can find where they are connected to the frame. Eventually, I found that both the heating element was broken and the thermostat was fried. It took a while looking at various websites to find the proper parts. It's all OK now.

Remove the two screws that hold the front cover. Remove front cover and disconneted wiring to door switch.Remove the cover ( lower right hand corner )back of the dryer to gain access to belt idler pulley/tensioner. Remove old belt and slide new belt on the tumbler.

After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!

The service from PartsSlect was outstanding.
Parts arrived next day and where OEM. I had the
dryer cleaned and operational in 1.5 Hr's
Keep up the great service.



Thank You

Remove the door and the plastic brackets on the other side of the door opening. Remove the front cover by gentally pulling from the top first. Support the dryer basket (I used an old towel and a block of wood. With a 1/2 inch wrench remove the Roller Shaft with the Drum Support still attached. Replace new shaft and drum support. (always replace both at the same time or you will find that the problem will come back much sooner.) Careful when installing. Make sure that the new non metalic washers (suppied) are propery seated when you are tightening down the nut.