MED6205RW0 Maytag Dryer - Instructions

Just insert filter.

unplugged the dryer and removed collapsable vent then we laid it on its back. took off the lower front face with a screwdriver ( just inserted in upper margin and it popped off) then removed a couple of screws and put the new element in replaced the screws and we cleaned all the old dust and lint from in the cabinet and replaced the front face. no problems.

Suggest you test all suggested parts first with ohm meter to determine cause of failure. Heater element was functioning properly, other parts were required to fix problem.

Just before leaving for vacation, we discovered that the dryer was not heating the air at all. Its an electric dryer, so did the basic troubleshooting, put ohm meter on the dryer element and found it was open circuit. Ordered the replacement element and it arrived while were were gone on vacation. My wife and daughter came home early from the beach to get kid ready to go to college. They needed the dryer, so I was able to walk them through replacing the element over the phone.

Amazing that they were able to get this done, but really just says how easy it was.

Exchanged old for new.

As per directions (videos) I found on PartSelect; 1st removed the bottom panel, then removed the housing (2 screws) covering the fan/lint trap area. Pulled the wires (2) from the heating element and removed three screws, 1 on the side of the housing immediately behind the heating element terminals, and 2 screws holding the stamped steel riser in place. I didn't have to remove the entire heater housing, but rather wiggled the heating element out slowly. For that I used a pair of pliers to grip the element and a gloved hand to hold the housing steady while I pulled one side then the other. I spent some time vacuuming out all the dust while I was in there. Replacing the element was a little easier, it slid in with firm hand pressure. Then just a matter of reversing the steps above. Wife was happy and once again, I am a hero.

Removed the front bottom panel. Disconnect the two wires and two screws and then remove the heater element using pliers. Then install the new heater element in the same way.It works good as new now! Thanks to PartSelect.

I actually had a friend's husband do the repair, who is an electrician by trade. He removed the front of the dryer, removed the box that held the element, removed the element, marked the wiring, and then when the part came, he put it back in, and reassembled the dryer.

I watched your online repair video, which was excellent. As I started the repair, it was exactly as described in the video....very easy. The only thing I did differently was clean out the mechanical compartment of the dryer with a shop vac.....simply because it was full of lint. There is nothing I won't try to fix; but this job can be done by anyone. Do it yourself; don't spend the money to have someone else do it.

Removed toe plate, make sure and use something like a 5 in 1 painters tool, makes the job easier as you will see a notch inside the seam between toe plate and outer shell, take 1 screw from heater tube cover I used a nut driver, this job is best to use with a stubby socket set, there are 2 machine screws with hex heads holding the heating element to the heating tube, you cant really see the heads but can feel them with your fingers, disconnect the 2 terminals in front of this, but make sure you use a blue or black sharpie to mark the terminals, use your stubby and remove screws, then use a set of needle nose pliers and pull out the heating element, the new heating element slide right in the grooves then reverse the take off process, good luck

i removed the old lens,then removed the bulb,after ordering and receiving your replacement lense,it went back on just like the old one.the repair was very easy. thank you. D.S P.S1 IAM A REPIARMAN NOW!!! WITH YOUR VIRTUAL REPAIRMAN APP,VERY VERY SMART ILL SPREAD THE WORD.

Removed back panel to get to inside. Removed drum etc to replace drum rollers (ordered repair kit also), replaced the idler pulley etc, now like new. Repair successful!!!! Thank you!

Took bottom accesses panel off dryer (two screws). To the right was heating element housing. Three screws to remove inside. One at the bottom of houseing bracket (holds up heating element housing) which connects to dryer cabinet floor. One at top of bracket (connects to bottom of heating element housing). One on the left side where the elements wires connect (screw goes through housing then through element side arm). Once the three screws are removed disconnect wires and pull element stright towards you. Once everything was diasembled I took shopvac in side machine and swept it all out. Just reassble the same way you took apart.

first turn off the power supply then ..removed the lower front cover. .removed the heat shield that covers the element. .. removed the element and replaced with the new one ..

It was very easy to repair and the 1-800 number is a grat resource for assistnat in locating the part.