DE712 Maytag Dryer - Instructions

removed seven screws to take door apart and replace button. Glad that you still had the part for a 25-year-old unit.

I removed the front 2 screws witha phillips shorty due to there proximity to the floor. I removed the heater plate the wiring and the heating element in about 10 minutes, the only issue I had was sue to the fact that the heater is 2 pieces and not totally cylindrical it was kind of a pain to get it back into the hole on the back side, I ended up having to form it better into a circle so that I could get it in. After that the rest putting it back together was no big deal. The unit now works great.

Replaced both rollers,shafts, bearings and snap rings.

I didn't think it would fit as it looked bigger then the old one, I called the service department and they were very helpful. They made note of the fact that I had called with questions in case I had to call again, but it worked, and no one laughed at me. It was very nice of them. Thank you for all the help

Per instructions I printed off online: took off door, then the front panel. Pulled out the old switch/button, connected the new switch/button, made sure the new button was working; put the panel back on then the door and DONE!

Not certain as to reason for no heat, I first completely disassembled the dryer. This probably wasn't necessary but since the dryer is around 28 years old, I wanted to inspect and test all wiring, thermostats, etc. Testing revealed that it was the dryer element and it was quite easy to remove and replace the entire heater assembly.

I'm glad I completely dissassembled the dryer because it gave me a chance to clean up a few decades of lint accumulation on and in every part. Reassembly was a little more problematic as it takes a couple of extra hands to hold and align the drum and the top once you've reassebled the base, sides and other parts. Not overly difficult, just make sure you note where all the wiring is to be reconnected and save the screws and bolts in a baggy until you're ready for reassembly.

Other than waiting for the part to arrive (3 days) time spent in dissassembly and reassembly wasn't much more than a couple of hours.

Unplug the dryer and pull it away from the wall so front and back can be accessed. Remove front panel. Remove front drum support. Remove rear access panel. Disengage drive belt from idler wheel. Make careful note of course of belt and which side is "outward". Remove drum through front. Remove Rollers using circlip pliers. Remove nuts behind shafts. Remove shafts. Clean-up area and parts before re-install.

Install new Shafts and nuts. Grease shafts. Install new Rollers, washers and clips. Drape drive belt over drum while reinstalling from front. Remount drive belt over drive and idler pullies from the rear access. During this step it helps to have a helper to position the belt around the drum in correct fore/aft position, lying flat and without twists, smooth side against drum. Install front drom support. Rotate drum to seat belt before closing up. Install rear panel cover. Install Front panel. Plug it in and turn it on for a test.

I had replaced other parts on this dryer before (drive belt, interlock switch), so knew how to remove the front. That is easy to do. Didn't even have to pull dryer away from the wall. Removed heater assembly. NOTE: take a picture, or note which wires go where! Took a chance that it was only the heating element after measuring the resistance of the element and noting that it was an open circuit (very high resistance). Could also have been something else in addition, but turned out, not. The hard part was getting the new housing assembly to fit in the circular hole at the back. It comes as a poor fit, not shaped right. I eventually just used pliers to bend in the edges, like crimping, and finally got it to fit in. Some pushing to get all screws back in place and now it runs and heats. A great dryer, over 30 years old, and still going. Well worth the effort to repair.

There were two screws to remove the front of the dryer. Then 4 screws to remove the front drum support. Remove the drum. Then one nut each on changing the back drum support rollers. Assemble the drum and front support in reverse, and door front, don't forget to put the new drive belt ovre the drum. Then from the rear panel opening, one screw to change the idler assembly. Easy

It took me a lot longer to plan the repair and decide to do it than to do the actual work, knowing what I know now, and having the parts, it would take less than half an hour. As there are no repair manuals available, it took one of these reports to give me the confidence I needed to proceed.
I first found out how to open the front (only two screews on the underneath part of the front cover) and opened it to hear the noise, (just put the cover to one side while still connected to the door switch),,,,, sprayed some WD40 all over the place and the noise went away temporarily (DO NOT DO THIS as the oil will burn off on top of heater unit and smell and smoke). I replaced the roller that the drum sits on (above the heating unit) to the right of the drum and the belt. You need a special tool that fits into the little holes in the ring retainer, I got it at Lowe's ($20 +/-). It is a Channellock plier that opens when you squeeze, you have to change the points (comes with it).
So, here is the squence: remove the front panel, disconnect the swhitch (it took some pulling), set aside; remove front drum assembly (only four screws looking at you) and it comes right out; the Drum is light and comes right out as well, it just sits in a dry channel. The belt will fall off.... take the retainer ring off the roller with the special tool... remove roller and replace with new washers (one on either side) replace the ring retainer (recommend getting new one) with same tool. If you remove the small panel in the back of the washer it is very eassy to replace the belt.... I did replace it although the old one looked almost new .. instructions and a diagram come with the parts you buy here by the way... which they should say... place belt on drum per instructions (solid side down), put belt inside the chanell on drum (it will climb to the correct position by itself) put on drum front cover to hold drum in place, and then sting belt on pulley from the back of the dryer. (diagram comes with belt otherwise look at it before taking off the drum) Replace front panel (after reconnecting switch) and you are off (if you want to test without the front panel you have to touch the switch wires to each other (use tape) and do not do plugged in...
After much anxiety but not that much work the dryer runs great and is as quiet as new.... I took the parts off before ordering by the way.... the order came within three days... I am happy to have PartSelect.com .. Maytag had not clue this model even existed.... Thanks

I took the access panel off the back, realized that belt was in very bad shape. Ordered a belt when I got that changed I put it back together and it still had a clunking noise. Found out that the blower wheel was rounded off where it goes over the shaft. So to change that I took the two front screws off, then the four hex screws off of the tumbler guide. There were eight or so screws over the blower wheel, took those out and the clamp on the blower wheel then used the snap ring pliers for the snap ring, then changed the wheel. Problem solved. This website is very helpful I would not have attempted to fix my dryer without this website.

First, it is IMPERATIVE that the dryer is unplugged from the wall or the appropriate breaker is turned off to prevent electrocution!!! The front of the dryer is removed by removing the two screws at the bottom of the front with a Phillips head screwdriver. Next, remove the door wiring from the wiring clamp and set front / door of dryer to the side. Next, remove the bulk head by removing four nuts from the sides with the appropriate nutdriver. The drum belt will have to be disconnected from the motor pulley by lifting the spring of the pulley to release belt tension. This can be done from the front or back access panel of the dryer. The back access panel gives you a better view of the motor pulley and attached belt. After removal of the belt from the motor pulley, the drum of the dryer can be removed. Next, remove the heat shield at the front of the dryer. It is held on with two nuts and can be removed using the appropriate nut driver. Next, remove the blower wheel housing cover using the appropriate nut driver. The blower wheel will be next. It can be removed by using a pair of pliers to remove the circular clamp. A pair of snap-ring pliers will also be need to remove the snap-ring also holding the wheel in place on the motor axle. After the blower wheel is removed from its housing, the housing will need to be removed. The housing is again held in place by several nuts and the appropriate nut driver will be needed to remove them. Next, take all wiring loose from the motor. It would be a good idea to photograph or note how and what wires were attached in specific locations on the wiring harness. The new motor may be different when it comes to wiring and will be accompanied by a wiring diagram and the needed connection ends for the wiring. If it is a different wiring layout, as was my motor that I ordered from this site, a set of wiring strippers / pliers will be needed to cut, strip, and crimp the new connectors. After wiring has been removed from the motor, remove the motor by removing two nuts with the appropriate nut driver from the bottom of the motor mount. The motor, mount, and pulley will then all come out as one piece. The motor will then need to be removed from the mount. This can be accomplished by using a flat head screwdriver and a hammer. Place the flat end of the screwdriver into the raised edge of the motor mount clamp and pull away from the locking bracket. If needed, use a hammer to give that extra tap to the end of the screwdriver to remove the clamps. After the motor is removed from the mount, an Allen wrench will need to be utilized to take the belt glide / seat off of the motor axle. You will also need the snap-ring pliers again to remove a snap ring from this axle as well. Clean the motor mount and dry thoroughly. Grease the pulley housing where it contacts the motor mount for smooth gliding against the mount. It is important that you use a NON-FLAMMABLE grease. This is the end of the "tear-down" phase. Now is a good time to vaccum and clean the inside of the dryer cabinet. This will help insure that excess lint and fuzz is removed to prevent an accidental dyer fire. Next, place the new motor back into the motor mount in reverse order. Make sure the belt glide / seat from the motor axle aligns with the belt marks on the pulley. Reassemble the dryer in reverse order, making sure to follow the wiring diagram provided with your new motor. Also you need to insure that the motor is turned at a 45 degree angle to allow the dryer drum to pass the motor without striking it. After reassembly, plug in the dryer and attempt to start. If your dryer does not start, troubleshoot the wiring first. Wiring was the most difficult part of this repair and working in the tight space provided was a trick. Also look up a video of the repair! This helped me tremendously. Videos can be found on this site or at YouTube.com.

Overall, the repair was pretty easy. I'm a 52 year old woman who has never done drier repair. I replaced both front glides, both drum support roller wheels, the idler pulley wheel and the tumbler and motor belt. Including vacuuming out the inside of dryer and washing down the inside and outside of dryer with cleaning wipes, the whole project took me 2 hours. (if done individually, time would have been 20-30 minutes). You must have correct tools, so I did have to purchase two tools that I didn't have. My only suggestion in replacing the idler pulley wheel and the tumbler/motor belt would be to take the small access panel off the back of the dryer for easier access to the parts.

I followed the videos provided, the only think I would added is cleaning the riding surface of the drum. In my case the drum had gunk on it from the old pads, witch got on the new pads causing it to continued to make noise.

It would be wise to also get the felt and belt, to replace them all the first time.

Looked in one of the back removable panels and saw the broken belt. Took the machines front panel off per a You Tube video and saw the repair was simple but too the time to vacuum out a large amount of Lint Debris that had accumulated over the past 34 years all over the inside of the machine which is dangerous.. After cleaning it all up I simply put the new belt on and put everything back together and it all works nicely again!